3M PELTOR ComTac XPI MT20H682FB Serie Manual Del Usuario página 8

Ocultar thumbs Ver también para PELTOR ComTac XPI MT20H682FB Serie:
Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 20
EN
3M™ PELTOR™ ComTac XPI
3M™ PELTOR™ ComTac XPI is a hearing protector with level-
dependent function for ambient listening and input for external
equipment. Differences in available features may appear on
specific models. Read these instructions carefully before use
and save for future reference.
1. COMPONENTS
A:1 Foldable headband (stainless steel sheet, leather)
A:2 Cup supporting arm (stainless steel)
A:3 Two-point fasteners (POM)
A:4 Cup
A:5 Battery lid
A:6 Microphone for level-dependent function for ambient
listening
A:7 Damping pad (PUR foam)
A:8 Ear cushion (PVC foil, PUR foam)
A:9 Speech microphone input (J22) (only specific models)
A:10 External input cable (PUR) (only specific models)
A:11[-] button
A:12 [+] button
A:13 Bone conduction microphone (only specific models)
A:14 Speech microphone (TPE, PC) (only specific models)
A:15 Neckband (stainless steel, TPO)
2. FITTING AND ADJUSTMENT
Note! Brush aside hair around your ears so the ear cushions (A:8)
fit snugly. Spectacle frames should be as thin as possible and fit
close to the head to minimize acoustic leakage.
2:1 Foldable headband (Fig. B)
(B:1) Slide out the cups and tilt the top of the cup out, as the
cable must be on the outside of the headband.
(B:2) Adjust the height of the cups by sliding them up or down
while holding the headband in place.
(B:3) The headband should be positioned across the top of your
head.
2:2 Neckband (Fig. C)
(C:1) Place the cups in position over the ears.
(C:2) Keep the headset in position and place the head strap on
top of your head and lock it tight in position.
(C:3) The head strap should be positioned across the top of
your head.
2:3 Speech microphone (Fig. D)
For maximum noise cancelling, the speech microphone should be
positioned close to your mouth (<3 mm).
2:4 Bone conduction microphone
The bone conduction microphone (A:13) should be positioned
between your jaw bone and chin bone for best performance.
3. USAGE/FUNCTIONS
3:1 Inserting batteries
Remove the battery compartment lids and insert the batteries
(2xAAA). The battery polarity must correspond to the marking in
the battery compartment. The lids must be pressed all the way
down to ensure good seal. Low battery level is indicated by a ghost
voice message "low battery", repeatedly.
3:2 Switching the headset on and off
Press and hold the [+] or [-] button for two seconds to switch
the headset on or off. The current setting is always saved when
the headset is switched off, except when in ear-plug mode. The
headset is automatically powered off after two hours of inactivity.
This is indicated by a ghost voice message during the last minute
before the headset switches off.
3:3 Volume
The volume setting adjusts the level-dependent function for
ambient sound. There are four level settings and a silent mode.
Silent mode is confirmed by a voice message. The volume is
limited to 82 dB(A).
3:4 Menu
Press and hold the [+] and [-] button for one second for the
menu. To step through the menu, press the [-] button briefly. The
menu steps are listed below as 3:5–3:8. At each menu step the
[+] button is used to change the setting and, if available, step
through the available settings. A ghost voice message confirms
each menu step, followed by the current setting. Changes are
also confirmed by a ghost voice message. After a few seconds
of no activity, the menu returns to volume mode. By pressing [+]
and [-], the volume setting can be instantly reached at any stage
of the menu.
3:5 Equalizer
The equalizer adjusts the tone for the level-dependent function
for ambient listening. There are four level settings: Low, Normal,
High and Extra High.
3:6 Microphone (only specific models)
The microphone setting is only used to switch between bone
conduction microphone and external microphone. "External"
is used when a boom microphone is connected to the external
input jack.
3:7 Factory reset
Resets all menu settings to the factory default values. This setting
needs to be confirmed by pressing [+] when the ghost voice says
"confirm factory reset".
3:8 Advanced settings
The advance settings menu includes the additional settings
described in 3:9– 3:14. The advance settings menu steps are
added to the normal menu steps when activated. It is automati-
cally de-activated when returning from the menu.
3:9 Release time
The release time setting adjusts the time before the limiter for
the level-dependent function opens after activation. It is adjust-
able in two levels: Fast and Slow.
3:10 Balance
The balance setting adjusts the volume balance between the
right and the left ear. There are seven level settings: Center,
Right/1, Right/2, Max right, Max left, Left/2, Left/1.
8
GB
Tabla de contenido
loading

Este manual también es adecuado para:

Peltor comtac xpi mt20h682bb serie

Tabla de contenido