Idiomas disponibles
Idiomas disponibles
OBJ_BUCH-0000000200-001.book Page 15 Monday, March 16, 2015 8:24 AM
To adjust the desired cable length, remove the spring
hook, loosen the cable at the cable wedge (b) and pull the
cable downward. Adjust the cable length and push the
cable upward again, until the cable wedge locks the cable
again. Guide the overlapping cable end (minimum length
5 cm) through ring (a) and reinsert the spring hook again.
(see page 9)
In case the spring breaks, the balancer will block the
cable. When the load setting is too low, the spring-break-
age safety feature can actuate and block the balancer. In
this case, turn the adjustment screw a few turns in the
"+" direction.
9 08 01 055 00 0, 9 08 01 056 00 0,
9 08 01 057 00 0, 9 08 01 058 00 0:
Reduce the load to lock the wire cable. Turn the locking
button until the red dot is visible.
Do not release the lock when the load
WARNING
is suspended.
To limit the drawing-in of the cable, loosen the 4 cable-
clamp screws at the cable clamp, adjust the cable clamp
and retighten the 4 cable-clamp screws again. The rubber
buffer and the spring must always be mounted between
the balancer housing and the cable clamp.
In case the spring breaks, the balancer will block the
cable. This is recognisable when the clearance of the
adjustment screw is approx. 4 mm.
When the load is too low, the spring-breakage safety fea-
ture can actuate and block the balancer. In this case, turn
the adjustment screw a few turns in the "+" direction and
pull the spring-breakage safety feature.
When the cable reel rotates too quickly (e.g., lock loos-
ened without load, rapid lifting and lowering of the load),
a centrifugal-force securing mechanism blocks the bal-
ancer. In case the centrifugal-force securing mechanism
no longer releases, have the balancer repaired by an
authorised FEIN specialist workshop.
Repair and customer service.
Repairs of the balancer and the accessories are to be car-
ried out through a FEIN customer service agent.
The current spare parts list of this product can be found
on the Internet under www.fein.com.
Continuously maintain and visually check the balancer.
Lubricate all exterior, moving parts as well as the friction
points of spring and safety hooks. Maintaining the cable
with acid-free grease will reduce wear considerably.
Check the wire cable and the securing cable once every
week (when using frequently more often) for damage,
wear and broken wire strands.
Secure the extended wire cable dur-
WARNING
ing cleaning and maintenance against
accidental drawing-in.
The wire cable may only be shortened through a FEIN
customer service agent.
9 08 01 012 00 8, 9 08 01 023 00 1,
9 08 01 055 00 0, 9 08 01 056 00 0,
9 08 01 057 00 0, 9 08 01 058 00 0,
9 08 01 052 00 4, 9 08 01 037 00 9:
Have a damaged wire cable replaced through a FEIN cus-
tomer service agent.
9 08 01 024 00 9, 9 08 01 025 00 3,
9 08 01 026 00 6, 9 08 01 027 00 0,
9 08 01 028 00 8, 9 08 01 029 00 2,
9 08 01 030 00 4, 9 08 01 054 00 6:
A new wire cable is available from the FEIN customer
service agent.
The wire cable can be replaced without opening the bal-
ancer housing.
Pull the wire cable out so that the wire-cable end
can be seen laterally in the balancer.
Lock the cable reel by pressing on the screw and
turning it by 90° with the appropriate screwdriver.
Loosen the wire cable at the fastening screw and
install a new wire cable.
Firstly, secure the wire cable against unintentional
drawing-in, then loosen the lock of the cable reel
and allow the wire cable to slowly draw into the
balancer housing.
Warranty and liability.
The warranty for the product is valid in accordance with
the legal regulations in the country where it is marketed.
In addition, FEIN also provides a guarantee in accordance
with the FEIN manufacturer's warranty declaration.
The delivery scope of your product may include only a
part of the accessories described or shown in this Instruc-
tion Manual.
Declaration of conformity.
FEIN declares itself solely responsible for this product
conforming with the relevant provisions given on the last
page of this Instruction Manual.
Technical documents at: C. & E. Fein GmbH, C-DB_IA,
D-73529 Schwäbisch Gmünd
Environmental protection, disposal.
Packaging, worn out products and accessories should be
sorted for environment-friendly recycling.
en
15
