Troubleshooting - ARIETE 1365 Manual De Instrucciones

TROUBLESHOOTING

If there are problems with operation, immediately turn off the machine and unplug it from the socket-outlet .
Problems Causes
The coffee maker There is little water and the pump
does not suck it up .
does not supply
steam .
The steam exit hole on the
dispenser wand is clogged
Coffee over- Probably an excess amount of
ground coffee has been placed
fl owing from the
in the fi lter ring preventing the
edges of the fi lter
fi lter ring from being correctly
ring .
tightened into its housing .
Residues of ground coffee have
remained on the gasket of the
fi lter holder coupling seat .
The hole of the silicone disc is
clogged .
The exit holes of the fi lter contai-
ning coffee grounds are clogged .
Faulty pod (MOD. 1366)
The coffee is not The perforated disc located in the
coupling seat of the fi lter holder
supplied or fl ows
has clogged holes .
too slowly .
The fi lter containing ground cof-
fee has the output hole clogged .
The coffee blend is ground too
fi ne .
The coffee blend is pressed down
too much .
The tanks is not inserted well .
The hole of the silicone disc is
clogged .
There is little water and the pump
does not suck it up .
Faulty pod (MOD. 1366)
Broken pod (MOD. 1366)
The coffee is too The blend has been ground too
coarsely .
watery and cold .
16
Solutions
Make sure the tank is fi rmly attached and check that the water
level in the tank is normal .
Fill with cool tap water up to the "MAX" level mark .
Unclog any deposits that may have formed in the hole of the
dispenser wand with a pin .
Slowly remove and disconnect the fi lter holder because any
remaining pressure could cause splashes or squirts . Clean the
coupling seat with a sponge (Fig. 14) . Repeat the operation
placing the correct quantity of coffee in the fi lter .
Clean the seal with a toothpick or a sponge (Fig. 14) .
Wash the silicone disc (B) under running water, bending it
slightly on the sides in order to free the centre hole of any
residue of coffee grounds that could clog it (Fig. 13) .
Slowly remove and disconnect the fi lter holder because any
remaining pressure could cause splashes or squirts . Clean the
clogged fi lter holes with a small brush or a pin . Clean the fi lter
using Ariete COFFEE CLEAN tabs, following the instructions
provided in the package .
Replace the pod in the fi lter holder (MOD. 1366)
Turn on the machine without the fi lter holder, making the water
run . Turn on the machine without the fi lter holder, making
the water run. If the water still does not come out from all the
holes evenly, carry out the descaling cleaning operation using
the Ariete NOCAL product found at Ariete service centres,
following the instructions provided in the package .
Slowly remove and disconnect the fi lter holder because any
remaining pressure could cause splashes or squirts . Clean the
clogged hole of the fi lter with the pin provided . Clean the fi lter
using Ariete COFFEE CLEAN tabs, following the instructions
provided in the package .
Try using coarser coffee blends .
amper coffee inside the fi lter using less pressure .
Fit the tank securely by pushing it as far as it will go .
Wash the silicone disc (B) under running water, bending it
slightly on the sides in order to free the centre hole of any
residue of coffee grounds that could clog it (Fig. 13) .
Make sure the tank is fi rmly attached and check that the water
level in the tank is normal . Fill with cool tap water up to the
"MAX" level mark .
Replace the pod in the fi lter holder (MOD. 1366)
Remove the fi lter holder, clean the seat with a sponge and
insert a new pod (MOD. 1366)
A more fi nely ground blend must be used to obtain a more
concentrated and hotter coffee . Anyhow, this problem is easily
solved thanks to the Thermocream® System, which always
guarantees hot coffee accompanied by a reach cream, even
with coarsely ground beans .