Tabla de contenido
Idiomas disponibles
Idiomas disponibles
4. Select "FF" with
/
buttons.
5. Press
key or turn off and on the radio.
6. Roger Beep is now deactivated.
Keypad/switching on beep
When switching on the radio, and pressing every key, (except for CALL,MON,PTT)
the radio sends out a beep. To deactivate it, follow these instructions:
1. Turn on the unit keeping pressed the
2. Select "BEEP" and "FF" with
FF
3. Press the
key or turn off the radio to confirm the operations.
Use of the ALAN 516 as Babyphone
This system is particularly helpful to take care of the baby while doing housework
at the same time.
To use this unit as Babyphone you need first of all two LPDs; ALAN 516 can
be used also with other LPDs models, too: the most important fact hereby is
that both devices are indicated with the same frequency setting. If using another
ALAN 516 for listening, the PTT/VOX switch must be in "PTT" position.
Setting up
1. Set the PTT-VOX switch of the transmitter in PTT position.
2. Turn on the unit keeping pressed the
3. Press the
button until the display shows:
4. Select the desired sensitivity level by the
5. Press
key: the display shows "bA-by". "bA-by" will be flashing after
1 minute (it indicates the function has been activated), and the RTX will
switch in Stand-by mode. The display stops flashing and the radio switches
in transmission mode when a signal/voice is heard. The LPD sends out
a note -similar to the CALL note- for 2 seconds. This note is heard from
the other LPD in RX mode: the radio switches in TX mode for 10 secs.
When the transmission is ended, the LPD switches in reception for 10
secs. This operation will be repeated for 3 times.
BABYSITTER function deactivates all other keys except the PTT and the lighting
key.
/
buttons.
key.
/
keys (min.01; max 06)
7
of the display.
The level sensitivity must be set as to the distance between the child and the
radio and the background noise level.
INTERCOM FUNCTION
Thanks to the INTERCOM-function, this transceiver is especially suitable for
the use on motorbikes. The DUPLEX function allows simultaneously
communications between driver and partner, as a phone conversation.
Connect the first headset to the Speaker/Microphone-jack at the top of the
transceiver and an optional accessory (throat activated microphones, etc.) to
the INT-jack of ALAN 516. To use this function, set the PTT/VOX switch in
PTT position.
ALAN 516 is now functioning as an Intercom system. To get in contact with
other motorbike drivers (using the same frequency), the transmit mode can
be done manually (PTT-switch) or by voice controlled system (VOX). In this
case, the "PTT-/VOX" switch must be in "VOX" position. It is also necessary
the use of an appropriate accessory.
SCAN function
The Scan function is used to check the traffic radio on the 8 channels before
transmitting.
There are 2 kinds: SCAN and B. SCAN
SCAN
To make Scan function operative, it is necessary:
a) turn on the radio by rotate clockwise
b) Press the
button: "SCAN" will be blinking on the display.
c) Press
/
buttons.
d) To stop Scan function, press "PTT" or
B.SCAN
It monitors the first free channel (without carrier) for 5 secs amongst the 69
available.
To activate/deactivate it, follow the instructions above described.
CTCSS: Continuous Tone Coded Signalling System
ALAN 516 can receive in two modalities:
a) open traffic: in this case you will hear any communication transmitted
on the selected channel.
b) group modality CTCSS/DCS: CTCSS and DCS tones are "access keys"
that allow you to receive only messages coming from parties using same
channel and code. Speaker will remain muted until the correct CTCSS or
DCS tone is received (further details will be explained in the successive
paragraphes).
the ON/OFF volume.
key.
8
Capítulos
Tabla de contenido
