Mellerware MSI-3001 Manual De Instrucciones página 6

MANUAL STEAM IRON MSI-3001 CRUCES.pdf
USE:
- Unroll the cable completely before plugging it in.
- Connect the appliance to the mains.
- Turn the thermostat control to the desired tempe-
rature position.
- Do not use temperatures higher than those indica-
ted on the garments to be ironed.
● Temperature for synthetic fibres (Polyester,
Nylon...).
●● Temperature for silk, wool. (Minimum
temperature for ironing with steam)
●●● Temperature for cotton.
Max Temperature for linen.
- If garment has various kinds of fibres, select the
temperature for the fibre that requires the lowest
temperature. (For example, select the temperature
for polyester for a fabric made out of 60% polyester
and 40% cotton).
- Wait until the pilot light (F) has gone out, indicating
that the appliance has reached an adequate
temperature.
- During use the pilot light (F) will automatically flash
on and off, indicating that the heating elements are
C
operating in order to maintain the desired tempera-
M
ture.
Y
DRY IRONING:
CM - The appliance has a steam flow regulator which,
when set to 1, allows dry ironing (without steam).
MY
STEAM IRONING:
CY
- It is possible to iron with steam whenever the tank
CMY
has water and the adequate temperature is
selected.
K
STEAM FLOW CONTROL:
- The appliance has a (C) control knob for adjusting
the steam flow.
SPRAY:
- The spray can be used in both steam and dry
ironing.
- Press the spray button ( A ) to use this operation.
- The spray button has to be pressed repeatedly to
release the first spray.
STEAM BLAST:
- This function provides extra steam for removing
creases.
- Press the steam blast button ( B ). Wait a few
seconds until the steam penetrates the fibres of the
garment before pushing the button again. For
optimum steam quality, do not apply more than
three successive blasts.
- The spray button has to be pressed repeatedly to
release the first spray.
6 3/9/18 8:44
VERTICAL IRONING:
- It is possible to iron hanging curtains, items of
clothing on their own hanger, etc. To do so, follow
these instructions:
- Select the iron's maximum temperature by turning
the iron's temperature regulator clockwise. (Fig 2)
- Iron from top to bottom while pressing the steam
control ( B ). Important: for cotton and linen, it is
recommended to put the base of the iron in contact
with the material. For other more delicate fabrics, it
is recommended to keep the base of the iron a few
centimetres away.
ONCE YOU HAVE FINISHED USING THE
APPLIANCE:
- Select the minimum position (MIN) using the
thermostat control.
- Unplug the appliance from the mains.
- Remove the water from the water tank.
- Clean the appliance.
CLEANING
- Unplug the appliance from the mains and let it cool
down before performing any cleaning task.
- Clean the appliance using a damp cloth with a few
drops of detergent and then dry it.
- Do not use solvents, or products with an acid or
base pH such as bleach, or abrasive products, for
cleaning the appliance.
- Do not immerse the appliance in water or any
other liquid, or place it under a running tap.
SELF-CLEANING FUNCTION:
- It is important to self-clean the appliance at least
once a month to remove calcium and any other
built-up minerals inside the iron.
- Fill the water tank to its maximum level, as indica-
ted in the "filling with water" section.
- Place the iron in an upright position, plug in to the
mains and select maximum temperature.
- Leave the appliance to heat up until the pilot light
indicates that it has reached its consigned tempera-
ture.
- Unplug the appliance and place it in the sink.
- Press and hold the self-clean button.
- Let the water flow out through the steam vents in
the base, while lightly shaking the appliance.
- Release the button after a minute or when the tank
becomes empty.
- Leave the iron in the upright position until it has
cooled.
* HOW TO DEAL WITH LIME SCALE INCRUSTA-
TIONS: