Before Use - Miniland digimonitor 2.4 gold Manual De Instrucciones

ENGLISH
unshielded cables will probably cause interference to
radio and television reception.
3.3. CHOOSING A SUITABLE LOCATION
· Place the electronic device out of the reach of
children in order to avoid accidents.
· Children can become entangled in cords. The baby
unit should be placed at a distance of at least 1 to 1.5
meters from the baby's cot. Never place the baby unit
inside the cot, bed or playpen, or attach the tripod to
them. Make sure the unit, cables and adapter are out
of reach of the baby and other young children.
· Place the baby monitor in a place where the air can
circulate freely. Do not place on soft quilts or blankets,
or in the corners of cupboards, shelves, etc.
· Place the baby monitor away from heat sources such
as radiators, chimneys, cookers and direct sunlight.
· Place the camera away from TV sets, repeaters and
radios. The intense radio signals generated by these
elements could cause noise or even sounds and
images to appear on the monitor. If this occurs, move
the camera to another location.
. This monitor can be placed on a tabletop by using
the retractable table stand on the back of the monitor.
When not in use, simply tuck the table stand away into
the back of the monitor until you hear a "click".
4. PRODUCT FEATURES
4.1. MONITOR FUNCTIONS AND CONTROLS
MONITOR
1. Charging LED
2. Power LED
3. Volume LEDs
4. LCD Screen
5. Menu/Back key
6. Nav UP & Vol up key
7. Nav RIGHT & Zoom key
8. Feeding Alert
9. Nav LEFT & Brightness key
10. Nav DOWN & Vol. Down key
11. Medicine Alert
12. Power button
13. Talk to the baby key
14. Confirmation key
15. Diaper Alert
16. Sleeping Alert
17. Microphone
18. Spaker
19. Micro USB DC Jack
20. Stand
21. Manufacturing code
DISPLAY
A) Signal level
B) Volume
C) Night vision
D) Zoom
E) Lullabies
F) Vox Mode
G) Selected camera
H) Battery level
I) Feeding alarm
J) Medicine alarm
K) Diaper alarm
L) Sleeping alarm
M) Date&Time
N) Locked touch panel indicator
O) Talk to the baby activated indicator
4.2. CAMERA FUNCTIONS AND CONTROLS
I. Retractable antenna
II. Photo sensor
III. Power button
IV. Hanging attachment
V. Speaker
VI. Link button
VII. Mini USB power connector
VIII. Microphone
IX. ON/link LED
X. Camera lens
XI. Infrared
XII. Tripod attachment
5. INSTRUCTIONS FOR USE

5.1. BEFORE USE

5.1.1. PARENT UNIT POWER AND BATTERY USE
The monitor, or parent unit, is designed to be used
with the battery or with the AC/DC adapter supplied.
Your baby monitor is supplied with a rechargeable
3.7V 1200mAh Li-ion battery for the monitor. Connect
the monitor to the adapter plugged into the mains
whenever possible, in order to keep the battery
charged.
BATTERY CHARGING:
When the level of battery is low, the charging LED (1)/
battery icon (H) will turn red and the monitor will start
to beep in every 5 seconds.
To charge your monitor:
1. Connect the power adapter to the micro USB
socket (19). For safety reasons, use only the adapter
supplied.
2. Plug the adapter into the mains. The battery pack
takes less than 8 hours to charge fully.
When charging:
3. During the charging process and if the unit is
ON, the battery icon (H) will show that the battery is
charging. While the monitor is charging, the charging
LED (1) will be light in red.
4. When the battery is full charged, the charging LED
(1) will turn to solid blue.
5.1.2. BABY UNIT POWER SUPPLY
The camera or baby unit of this baby monitor is
designed to be used with the AC/DC adapter supplied.
1. Connect the adapter cable to the mini USB socket
of the camera (VII). Use only the adapter supplied.
2. Plug the adapter into the mains.
Warning: Choking hazard – Keep the cord out
of the baby's reach. NEVER place a camera with
cables less than 1 meter from the cot. Never use
extension cords with AC adapters. Use only the
AC adapters supplied.
5.2. OPERATION
5.2.1. TURNING THE UNITS ON/OFF
5.2.1.1. MONITOR:
Press and hold the Power button (12) to turn the
monitor ON. When the monitor is turn on, the screen
will display the welcome screen and the power LED
20