Factory Reset - Comunello QUAD 24V 2M ONE Instrucciones De Uso

Enable/Disable Release Stroke
Enable/Disable Slam Lock
Remote controls
Read saved codes and set function
Assign a text string for each code
Delete single code
Add a new code
Check the presence of a code
Photocells
Enable/Disable Partial Inversion during Closing cycle
Enable/Disable Partial Inversion during Opening cycle
Enable/Disable Follow-Me
Operation test
Assign a text string for each photocell
Set the MODE (operation) of each photocell
Key switches
Operation test
Assign a text string for each key switch
Set the MODE (operation) of each key switch
Flashing lights
Enable/Disable Closing Pre-Flash
Enable/Disable Opening Pre-Flash
Enable/Disable Fast Flash during Opening cycle
Enable/Disable Fast Flash during Closing cycle
Enable/Disable Flash during Pause
Operation test
Assign a text string for each key flashing light
Interface I/O
Operation test
Assign a text string for each Interface I/O
Set the MODE (operation) of each Interface I/O
Utility output
Set Electric lock activation time (1"..20")
Diagnostics
Display the number of Manoeuvres Performed
Display the number of Operator Hours of operation
Display the number of System Life Hours
Display the number of Resets
Display the number of Stops (STOP commands)
Display the number of Encoder notches

FACTORY RESET

If there is need to restore the control unit to its factory settings, press
simultaneously the RESET, TX CODE, AUTOSET and STEP BY STEP
buttons, release only the RESET button (holding the others pressed), until
the AUTOSET led begins to flash. Now you can release the other buttons (TX
CODE, AUTOSET and STEP BY STEP), and the TX CODE led begins to flash
Once TX CODE led stop flashing, wait until the AUTOSET led turns on for a
while and then its turning off will confirm the control unit resets all parameters
to their initial factory settings.
DIAGNOSTICS
Photocell (DS) management in case of a fault
The photocell management (DS) in case of a fault of AT LEAST ONE OF
THOSE ACQUIRED during installation will INHIBIT CLOSING of the gate
(excluding virtually all cases of controlled or automatic closing). If a photocell
previously acquired experiences a fault, the automation will stop, which will
only be able to open (for safety reasons), but will never be able to close,
except following:
1. Disabling of the safety devices (DS) via the DIP switch #10 (ON)
2. Reacquisition of the missing DS (with the same ID of the faulty device)
Disabling of the safety devices (emergency operation)
Disabling management of the DS (photocells, locks, etc.) allows the control
unit to "eliminate logically" the DS that are faulty/missing, but continuing
to manage consistently the settings of the functional DS installed on the
system. Essentially, disabling the safety devices (DS) does not eliminate the
photocells installed and that are functional (raising safety issues), but only
34
COMUNELLO ®Copyright 2015 - All right reserved
those that are no longer functional.
Reacquisition of the missing DS (fault repair)
If a photocell (DS) experiences a fault, the automation operates according
to the function set on the faulty DS (e.g.: if the photocell is set ON OPEN,
when the DS experiences the fault, the gate stops and will not restart until
disengaged, which will never occur, due to the presence of the fault). If you
do not want to intervene by disabling the DS via DIP switch #10, you will have
to repair the fault, i.e. replace the faulty DS with an equivalent one having the
same ID. Once you have reconnected the repaired DS, you have to run the
(DETECT) procedure again by
a. Pressing the RESET button in the control unit
b. running DETECT on the ONE app
CAUTION: By pressing the RESET button, all the accessories connected
are recognised, the HW parametres on the board (trimmer adjustments, DIP,
SLIDE, etc.) are checked again and the FIRST OPENING MANOUEVRE is
set. If the gate is completely open (safety manouevre), this can cause a stop
on opening and a new command must be sent to close the gate.
BLACK-OUT MANAGEMENT
In the event of a power failure (or following the logic RESET, i.e.: pressure of
the key RESET on control unit), the system always makes a short opening
manoeuvre, followed by a closing manoeuvre in safety speed (receiving the
following command).
WARRANTY
Fratelli Comunello SpA provides a warranty for 24 months for the correct
functioning of the actuators from the date of manufacture, provided that
the performance specications indicated in the product instruction manuals
are respected. Free of charge repair and replacement of components
that are found to be faulty according to the indisputable judgment of the
company's technical staff shall be guaranteed at the sole discretion of
Fratelli Comunello Spa, and so excluding any claim for damages made
by others. Warranty material shall be returned to Fratelli Comunello S.p.a.
headquarters carriage paid and will then be shipped to the customer
carriage unpaid. The material found to be faulty and returned to Fratelli
Comunello S.p.a. shall remain property of the Seller. Any cost resulting
from any work needed to repair the defect or to replace the material shall
be charged to the Buyer. No compensation shall be allowed for the period
of device inactivity. Work under warranty does not prolong the warranty
period. The defect of the product shall be reported by the Buyer within 8
(eight) days from its discovery or from the date of delivery of the goods,
under penalty of invalidation of the warranty. Such claim shall be notied
in writing.
Warranty does not cover:
Any product defect or damage that may have been incurred during
transport; any defect or damage arising from any fault and/or from
neglect, inadequacy and misuse of the electrical wiring in the Buyer's
property; any defect or damage caused by any repairs carried out by
non authorised personnel or by incorrect use/installation (with reference
to this, system maintenance is recommended every 6 months) or if
not original spare parts are used; any defect caused by chemicals or
atmospheric conditions. The warranty does not cover any cost neither
for consumable materials nor for alleged defects or convenient surveys.
Product Features Fratelli Comunello SpA products are subjected to
continue changes and improvements; their technical features and image
may therefore change without previous notice.
Competent court
Since the contract of sale is conrmed by an Order Conrmation drawn up
in Rosà, any such dispute shall be settled by the laws of Italy and by the
court of Vicenza (VI).
FAQ
FAQ. Question FAQ. Question
Can I use 24 VDC NO. The ONE system necessarily requires
operators without an the use of 24VDC operators with encoder
encoder? to work properly, run precise movements
and ensure safety (obstacle detection).