De Dietrich DHT316XE1 Instrucciones Para Instalación Y Uso página 5

ENGLISH
WARNING
The distance between the supporting surface for the cooking worktop on the hob and the lower part of the
hood must be at least 65 cm. If the instructions for installation for the hob specify a greater distance, this
has to be taken into account.
The air collected must not be conveyed into a duct used to blow off smokes from appliances fed with an
energy other than electricity (central heating systems, thermosiphons, water-heaters, etc.).
Comply with the official instructions provided by the competent authorities in merit when installing the disposal
duct. In addition, exhaust air should not be discharged into a wall cavity, unless the cavity is designed for
that purpose.
The room must be well ventilated in case a hood and some other heat equipment fed with an energy other
than electricity (gas, oil, coal heaters, etc) operate at the same time.
The intake hood could create a vacuum indeed by extracting the air out the room. The vacuum should not
exceed 0,04mbar. This prevents the head source to generate in-drawghts of gas that must be extracted out.
Check the data label inside the appliance; if the symbol (
has such technical particularities that it belongs to class II insulation, therefore it must not be earthed.
The following warning is valid in the United Kingdom only: in case your cable is not furnished with a plug,
read the following instructions; as the colours of the wires in the mains lead of this appliance may not
correspond with the coloured markings identifying the terminals in your plug, proceed as follows: – the wire
which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black;
– the wire which is coloured brown must be connected to the terminal which is marked with the letter L or
coloured red. – terminal of a three-pin plug.
Check the data label inside the appliance; if the symbol (
ATTENTION: This appliance must be earthed. When making the electrical connections, check that the current
socket has a ground connection.
The following warning is valid in the United Kingdom only: in case your cable is not furnished with a plug,
read the following instructions; as the colours of the wires in the mains lead of this appliance may not
correspond with the coloured markings identifying the terminals in your plug, proceed as follows:
– the wire which is coloured green and yellow must be connected to the terminal in the plug which is marked
with the letter E or by the earth symbol [
is coloured blue must be connected to the terminal which is marked with the letter N or coloured black; –
the wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured
red.
When making the electrical connections, check that the voltage values correspond to those indicated on the
data plate inside the appliance itself. In case your appliance is not furnished with a non separating flexible
cable and has no plug, or has not got any other device ensuring omnipolar disconnection from the electricity
main, with a contact opening distance of at least 3 mm, such separating device ensuring disconnection from
the main must be included in the fixed installation. If your unit features a power lead and plug, position this
so the plug is accessible.
Always switch off the electricity supply before carrying out any cleaning or servicing operations on the
appliance.
USE
Avoid using materials which could cause spurts of flame (flambées) near the appliance.
When frying, take particular care to prevent oil and grease from catching fire. Already used oil is especially
dangerous in this respect. Do not use uncovered electric grates.
To avoid possible risks of fire always comply with the indicated instructions when cleaning anti-grease filters
and when removing grease deposits from the appliance.
MAINTENANCE
Thorough servicing guarantees correct and long-lasting operation.
Any fat deposits should be removed from the appliance periodically depending on amount of use (at least
every 2 months). Avoid using abrasive or corrosive products. To clean painted appliances on the outside,
use a cloth dipped in lukewarm water and neutral detergent. To clean steel, copper or brass appliances on
the outside, it is always best to use specific products, following the instructions on the products themselves.
To clean the inside of the appliance, use a cloth (or brush) dipped in denatured ethyl alcohol.
) is printed, read the following: this appliance
) is NOT printed, read the following:
], or coloured green or green and yellow; – the wire which