Useful Information - Chicago Pneumatic CPA5000 Información Sobre Seguridad

Unidad neumática de extracción de polvo

página de 104

/ 104
Contenido
Tabla de contenido

Tabla de contenido

Idiomas disponibles

Safety Information

4. Replace the Inlet Cap (A)

• Clean / Wipe the top edge of the canister to ensure a good

seal when the inlet cap is attached.

• Replace the inlet cap (A) on the canister (C) and rotate

clockwise approximately 1 full turn until snug.

HEPA filter change

See figure 7

If this vacuum is used to collect hazardous material, appro-

priate personal protective equipment may be required. The

HEPA Filter (A) should be replaced if damaged or when dust

accumulation on the HEPA filter degrades vacuum perfor-

mance.

1. Safe the Vacuum

• Disconnect the compressed air source from the vacuum.

• Disconnect the vacuum hose.

2. Unbox a new HEPA filter (A)

• Remove the HEPA timer card from the box and set aside.

• Remove the HEPA filter (A) from the box and unwrap.

3. Remove the Inlet Cap (C)

• Hold the vacuum canister (F) and rotate the inlet cap (C)

counterclockwise approximately 1 full turn.

• Remove the cap from the canister.

4. Remove the HEPA filter (A) with Pre-Filter from the

Inlet cap

• Hold the Inlet Cap (C) in your left hand.

• Grasp the bottom of the HEPA filter (A) with your right

hand and turn counter clockwise approximately 3 full turns.

• Remove the HEPA filter (A) and Pre-Filter (B).

• Dispose of the HEPA filter (A) and Pre-Filter (B) according

to your company policy

5. Install a new HEPA filter (A)

• Hold the Inlet Cap (C) in your left hand.

• Grasp the bottom of the HEPA filter with your right hand

and turn clockwise approximately 3 full turns .

• Tighten the HEPA filter (A) until it hard stops Optional.

• Using a 3/4 inch 6 point socket and torque wrench ensure

the filter is tightened to 46 in/lbs of torque.

6. Install a new Pre-Filter on the HEPA filter (A)

• Lay the inlet cap (C) assembly upside down on a work sur-

face.

• Stretch a new Pre-Filter (B) over the HEPA filter (A).

• Pull the Pre-Filter on to the HEPA filter(A) until the entire

HEPA filter is covered.

• Ensure the Pre-Filter elastic is touching the bottom of the

inlet cap (C).

• Ensure the Pre-Filter elastic is NOT seated between the

HEPA filter gasket and the bottom of the inlet cap (C).

7. Replace the inlet cap (C)

• Clean / Wipe the top edge of the canister (E) to ensure a

good seal when the inlet cap is attached.

• Replace the inlet cap (C) on the canister (F) and rotate

clockwise approximately 1 full turn until snug.

8. Activate the HEPA filter timer

• Remove the old HEPA timer card from the top handle of

the vacuum.

• Attach the new HEPA timer card with a zip tie (included)

to the top handle of the vacuum.

• Follow the directions on timer card to activate.

Disposal

• The disposal of this equipment must follow the legisla-

tion of the respective country.

• All damaged, badly worn or improperly functioning de-

vices MUST BE TAKEN OUT OF OPERATION.

Safety information

• A HEPA Filter must be installed in this vacuum at all

times.

• If this vacuum is used to collect hazardous material, ap-

propriate personal protective equipment may be re-

quired.

• Use the device uniquely in work situations for which it

was designed and built.

• Never leave the appliance unattended during working

phases. Do not leave the appliance unattended and

poised or stairs, or in places where the balance is poor.

• The appliance must be disconnected from its power

source during cleaning or maintenance and when replac-

ing spare parts.

• Do not start the machine in case of suspected failure.

• Do not leave the operating unit unattended or within

reach of children, animals, or people are not aware of

their actions.

• Do not use the device in all situations of uncertainty or

abnormalities usually, though not mentioned in this man-

ual.

Any alteration to this equipment by a third party will nullify

its warranty.