Tabla de contenido
Idiomas disponibles
Idiomas disponibles
5.2
Time Menu
The time display flashes on the screen when the time has not yet been set or after a
4-hour power outage. Use the Time menu to select the time format (12-hour or 24-
hour) and to set the clock and date.
NOTE: The date is used to determine the sunset and sunrise times.
5.3
Configuration Menu
(Conf)
Use the Configuration menu to set the following parameters (see sections 5.3.1 to
5.3.4).
5.3.1 Backlight mode (SCRN)
The screen is lit at high intensity for 8 seconds when you press any button. The rest of
the time, depending on the backlight mode selected, the screen behaves as follows:
Scrn Off: The screen is not lit.
Scrn On HI: The screen is lit at high intensity.
Scrn On LO: The screen is lit at low intensity (default mode).
5.3.2 Automatic Daylight Savings Time Changeover
(DLS)
When automatic daylight savings time changeover is on (DLS On), the RPLS540A/
RPLS541A changes to daylight savings time (summer time) at 2:00 am on the second
Sunday of March and changes back to normal time (winter time) at 2:00 am on the
first Sunday of November. This function is enabled (DLS On) by default.
5.3.3 Latitude and Longitude Coordinates (LAT and
LONG)
The coordinates are used to turn the lights on at sunset and off at sunrise. The latitude
is set to +45 and longitude to -75 by default. These settings provide approximate
sunset and sunrise times for most North American cities. To obtain your city's
coordinates (or those of a nearby city), see the coordinates table. You can also obtain
this information at www.geonames.org or with a Global Positioning System (GPS)
device. The accuracy of the sunset and sunrise times depends on the accuracy of the
coordinates you enter for your city.
NOTE: Enter a negative value for a south latitude or a west longitude.
5.3.4 Correction Factor (ADJ)
If your city's time zone is based on political or economic boundaries instead of its
coordinates, your lights might switch on or off too early or too late with respect to
sunrise and sunset. In this case, apply a correction factor (+1 or -1 hour; refer to
addendum). Otherwise, leave it at 0 (default value).
5.4
Program Menu
(Prog)
Use the Program menu to set the programs; i.e. the times you want the lights to turn On
or Off when the switch is in Automatic mode. To set a program, proceed as follows:
Select a program number (see section 5.4.1)
Set the day(s) of the program (see section 5.4.2)
Set the program start time (see section 5.4.3)
5.4.1 Selecting a program number
You can set up to 7 "On" programs ("P01 On" to
"P07 On") and 7 "Off" programs ("P01 Off" to
"P07 Off"). Select an "On" program to set when to
turn the lights on. Select an "Off" program to set
when to turn the lights off.
5.4.2 Setting the day(s) of the
program
After selecting a program, set the day(s) of the program. You can select a specific day,
all 7 days or "none". Choose "none" for any unused program.
5.4.3 Setting the program start time
After setting the day(s) of the program, set its start time. You can select either a specific
time, the sunset time or the sunrise time:
•
To select a specific time:
(1) Advance to the hour setting and select the hour.
(2) Advance to the minutes setting and select the minutes.
RPLS540A/RPLS541A
•
To select sunset or sunrise time:
(1) Advance to the hour setting and select the sunset time or sunrise time. (When
you scroll, the sunset time
12 am.)
(2) To enter an offset (from -70 to +70 minutes in 10-minute increments)
between the sunset or sunrise time and the program start time, advance to the
minutes setting and change the minutes.
EXAMPLE: If the sunset time is 6:13 pm and you change the minutes to
•
display 6:43 pm, you have entered a delay of 30 minutes. If, later in the year,
the sunset time is 4:01 pm, the program will start at 4:31 pm.
NOTE: When you enter an offset,
•
display the sunset or sunrise time. To remove the offset, display the sunset or
sunrise time and change the minutes until
5.4.4 Examples
Example 1: The lights turn on at sunset and off at 11:00 pm every day (default
setting).
Program
P01 On
P02 On to
P07 On
Example 2: The lights turn on at sunset and off at sunrise every day.
Program
P01 On
P02 On to
P07 On
Example 3: The lights turn on at 8:00 pm every day and turn off at 10:00 pm every day
except on Saturday night when they turn off at 1:00 am.
Program
Days
P01 On
All 7 days
P02 On
None
P03 On
None
P04 On
None
P05 On
None
P06 On
None
P07 On
None
Be careful about overlapping!
For example, if you set "P01 Off" at 10:00 pm for all 7 days and set "P02 Off" to 11:00
pm for Saturday, on Saturday, the lights will turn off at 10:00 pm, not 11:00 pm since
"P01 Off" is set to an earlier time than "P02 Off".
Reset to Default Settings
To return the switch to its default settings, simultaneously press both
"P01 On"
"P01 Off"
main and left buttons and hold. The software version will appear for
5 seconds. RST will appear for the next 5 seconds. Release the
buttons when all segments appear on the screen. The switch is now
reset (see default settings in the menu flowchart).
Troubleshooting
The screen is blank.
The display is faded or
irregular.
The metal plate is hot.
and sunrise time
appear between 11 pm and
appears along with
or
disappears.
Days
Time
Program
Days
All 7
sunset
P01 Off
All 7
days
days
None
—
P02 Off to
None
P07 Off
Days
Time
Program
Days
All 7
sunset
P01 Off
All 7
days
days
None
—
P02 Off to
None
P07 Off
Time
Program
Days
8:00 pm
P01 Off
Sunday (Su)
—
P02 Off
Monday (Mo)
—
P03 Off
Tuesday (Tu)
—
P04 Off
Wednesday (We)
—
P05 Off
Thursday (Th)
—
P06 Off
Friday (Fr)
—
P07 Off
Sunday (Su)
• A light bulb is burned out.
• The safety switch is pulled out (see section 4).
• The load is less than 40 W.
• The ambient temperature is either below or above
the switch's operating temperature.
This is normal with high loads (maximum of 500 W).
The sunset or sunrise time
• The date or time is wrong (see section 5.2).
is inaccurate.
• The longitude or latitude is wrong
• The correction factor is wrong
• You have entered an offset
Specifications
when you
Supply: 120 VAC, 60 Hz
Minimum load: 40 watts
Maximum load: 500 watts
Operating temperature range: -15 °C to 50 °C (5 °F to 122 °F)
Storage temperature range: -40 °C to 60 °C (-40 °F to 140 °F)
Power outage: The screen is blank. Only the time must be set if the outage lasts more
than 4 hours; all other settings and programs are permanently saved
Time
Latitude range: from -65° to +65°
11:00
Solar table precision: +/- 11 min. (within ±60° latitude)
pm
Certification: UL (c UL us)
—
Warranty
Resideo warrants this product, excluding battery, to be free from defects in
Time
workmanship or materials, under normal use and service, for a period of one (1) year
sunrise
from the date of first purchase by the original purchaser. If at any time during the
warranty period the product is determined to be defective due to workmanship or
materials, Resideo shall repair or replace it (at Resideo's option).
—
If the product is defective,
(i) return it, with a bill of sale or other dated proof of purchase, to the place from which
you purchased it; or
(ii) call Resideo Customer Care at 1-800-468-1502. Customer Care will make the
determination whether the product should be returned to the following address:
Time
Resideo Return Goods, 1985 Douglas Dr. N., Golden Valley, MN 55422, or whether a
10:00
replacement product can be sent to you.
pm
This warranty does not cover removal or reinstallation costs. This warranty shall not
apply if it is shown by Resideo that the defect was caused by damage which occurred
10:00
while the product was in the possession of a consumer.
pm
Resideo's sole responsibility shall be to repair or replace the product within the terms
10:00
stated above. RESIDEO SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY
pm
KIND, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING,
10:00
DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY, EXPRESS OR
pm
IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT.
Some states do not allow the exclusion or limitation of incidental or consequential
10:00
damages, so this limitation may not apply to you.
pm
THIS WARRANTY IS THE ONLY EXPRESS WARRANTY RESIDEO MAKES ON THIS
10:00
PRODUCT. THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE
pm
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
1:00 am
IS HEREBY LIMITED TO THE ONE YEAR DURATION OF THIS WARRANTY. Some states
do not allow limitations on how long an implied warranty lasts, so the above limitation
may not apply to you.
This warranty gives you specific legal rights, and you may have other rights which vary
from state to state. If you have any questions concerning this warranty, please write
Resideo Customer Care, 1985 Douglas Dr, Golden Valley, MN 55422 or call 1-800-
6.
468-1502.
Customer Assistance
If you have any questions about your light switch, go to
http://customer.resideo.com, or call Customer Care toll-free at 1-800-468-1502.
CAUTION: ELECTRONIC WASTE NOTICE
7.
The product should not be disposed of with other household waste. Check for the
nearest authorized collection centers or authorized recyclers. The correct disposal of
end-of-life equipment will help prevent potential negative consequences for the
environment and human health.
(see section 5.3.3).
(see section 5.3.4).
(see section 5.4.3).
8.
9.
10.
11.
2/8
Tabla de contenido
