Valex BS 600 Instrucciones Para El Uso página 9

ADJUSTMENTS
IMPORTANT! Before carrying out inspections and mainte-
nance, unplug the machine from the power socket and make
sure that the switch is in the off position (0). Always wear
protective gloves during the following operations.
DIVIDER KNIFE ADJUSTMENT (Fig.F)
Carry out this operation whenever the blade is replaced and
at regular intervals.
Remove the blade protection (2) and the blade guide insert
(Fig.E pos.3).
Loosen the screws (1) and align the knife (4) with the blade.
Adjust the distance between these two elements between 3 and
5 mm at each point. Replace the screws (1) and reassemble all
the other components following the respective instructions.
OPERATIONAL TIPS
IMPORTANT! Always use the personal protective equipment re-
quired by safety regulations and the precautions listed herein.
When your hands are in the vicinity of the blade during cutting
operations, always use the relative piece pusher to push the pie-
ce (Fig.G pos.1); you will thus protect your hands from injury.
While cutting, keep the piece rested on the work surface and the parallel guide.
When cutting long pieces, support them after cutting to prevent
them from tipping up, using specific pedestals.
Push the piece against the blade slowly and evenly so as not
to place excessive stress on the motor and the blade.
PARALLEL CUTS
Use the parallel guide (Fig.A pos.2). Adjust it to the desired
position, loosening the handwheels and making use of the mil-
limetre rulers (Fig.A pos.4). Screw the handwheels back in.
45° CUTS
Use the set square (Fig.A pos.12). Insert the set square into
the parallel guide housing (Fig.A pos.2); the piece to be cut
should be rested in the set square "V" housing.
MAINTENANCE
IMPORTANT! Before carrying out inspections and mainte-
nance work, switch the machine off, unplug it from the power
supply and make sure that the blade is stationary.
- Clean and maintain your machine regularly, to ensure that it
remains perfectly efficient and has a long working life.
- At the end of each job, clean the machine completely.
- Periodically check the state of wear of the blade, replacing
it when it shows signs of cracks, deformations or uneven
consumption.
- When cleaning the machine, only use a cloth and a soft brush.
- Do not use any detergents or solvents as these may damage
the machine beyond repair.
Contact an authorised service centre for new or replacement
spare parts.
SPARES
TROUBLESHOOTING
If the machine fails to start: - check if all the electrical connec-
tions are firmly plugged into the mains. Check if the trip switch
has tripped. Check if a fuse has blown in your own electrical
system. It the problem persists following these checks then
the problem could be in the machine so have an authorised service centre check it.
Follow the tips below to store the machine:
1) Clean the machine and all its accessories thoroughly (see
maintenance section).
2) Store the machine: out of reach of children; in a stable and
safe position; in a warm and dry place; avoid excessively
high or low temperatures.
3) Protect the machine from direct light, if possible keeping it
in the dark or semi-dark.
4) Do not seal it in nylon bags where humidity could occur.
DEMOLITION
In order to safeguard the environment, proceed in compliance
with local regulations.
Do not dispose of the packaging, but reuse it where possible.
When the machine is no longer usable or reparable, dismantle
the various parts for differentiated refuse collection.
Amendments: - The text, figures and data correspond to the
standard in place on the date of printing of this manual. The
manufacturer reserves the right to update the manual should
any changes be made to the machine.
DECLARATION OF CONFORMITY
The firm indicated below declares, under its own responsibility, that
the product cited there complies with the essential health and safety
requirements contained in the following European directives:
98/37/CE, 89/336/CE, 73/23/CE and subsequent modifications.
PRODUCT: Saw Bench BS600
Product code: 1432513
Valex S.p.A. Via Lago Maggiore, 24 - Schio (VI) Italy
Schio, October 2002
Attorney - Bruno Anzolin
The product is protected by law against all non-conformities
with respect to the stated characteristics, as long as it has been
used solely in the way described in this user's manual, it has
not been tampered with in any way, it has not been repaired
by unauthorised personnel and only original spare parts have
been used. Problems caused by normal wear (such as cutting
elements, belts, bulbs, lubricants, etc.) are also excluded. Take
the product to your retailer or an authorised service centre,
exhibiting proof of purchase.
9
STORAGE
GUARANTEE