Ec Declaration Of Conformity - Carl Stahl Kromer 7241 Instrucciones De Empleo

Ocultar thumbs Ver también para 7241:
Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 18
Replacing the housing
(C) Removal/Dismantling:
Release the spring tension, proceeding as follows:
Apply a size-17 socket spanner to the endless screw (9),
then turn the spanner in the direction of the "-" symbol until
the cable no longer retracts. The spring fracture safeguard
now blocks the cable drum. Do not slacken the spring too
much in order to prevent spring destruction.
Unscrew the cover disk of the worm wheel and remove the
disk.
Unscrew the housing cover. Remove the circlip on the
worm wheel using special pliers. Pull the cable drum with
the spring and the shaft out of the housing, paying attention
to the feather key located in the shaft. If necessary, force
the shaft through the worm wheel with a plastic-faced ham-
mer. Put the brass washer located between the housing and
the cable drum back onto the shaft if appropriate. Unwind
the cable from the cable drum, detach it and pull it out of
the housing. Remove the suspension (see Replacing the
suspension).
(D) Reassembly/Reinstallation:
Fit the suspension to the new housing (see Replacing the
suspension). Insert the worm wheel into the housing, then
insert the cable drum with the shaft and the brass washer as
well, pushing the shaft through the worm wheel (thereby
ensuring that the feather key is correctly positioned relative
to the worm wheel; rotate worm wheel if necessary). The
shaft's ring groove must be visible. Insert the circlip into the
shaft's ring groove using special pliers.
Rotate the endless screw in the "+" direction to turn the
cable drum until the cable coupling is visible in the housing
slot. Insert the cable through the mouth of the housing and
install it as described under Replacing the cable. Wind up
the cable via the endless screw, rotating it in the "+" direc-
tion (using a size-17 socket spanner). Be sure that the cable
winds up correctly in the groove!
Tension the spring and adjust the load as described under
Replacing the spring assembly – see
Replacing the cable drum
Dismantle the zero gravity balancer as described under
Replacing the housing – see
however, to remove the suspension from the housing.
Installing a new cable drum:
Unscrew the cover and insert the shaft into the cable drum,
taking care that the ball bearing is not knocked out of the
drum.
Put the brass washer on the shaft and place the worm
wheel into the housing. Insert the cable drum with the shaft
and the brass washer into the housing, pushing the shaft
through the worm wheel. The feather key must engage with
the groove; rotate the shaft if necessary. Secure the worm
wheel with a circlip.
Insert the spring assembly into the drum as described under
Replacing the spring assembly
Reinstallation. Thereafter, install the cable as described
under Replacing the housing
stallation", section 2.
(B).
(C). There is no need,
(B) Reassembly/
(D) Reassembly/Rein-
Replacing the suspension
Remove the split pin, washer, bolt and tube of the suspen-
sion from the housing, then remove the suspension as well.
Insert the new suspension, push the bolt through the hous-
ing suspension and the tube, then secure it with the washer
and a new split pin.
Warranty
We warrant the functionality of this product and the flaw-
lessness of its materials for a period of 24 months, starting
on the date of delivery. However, this warranty excludes the
effect of normal wear and tear, overload, improper use or
use of non-original (third-party) spare parts.
Claims under this warranty can only be accepted if the
product has been handed over to us in undismantled condi-
tion for examination.
Any damage caused by a manufacturing defect or the use
of faulty materials will be remedied free of charge through
replacement or repair.
Our Standard Terms and Conditions shall apply.

EC Declaration of Conformity

We hereby declare in sole responsibility that the spring
balancers have been developed, designed and manufactu-
red in compliance with the applicable EC Directive relating
to machinery (2006/42/EC).
Besides, the following standards have been applied: DIN EN
12100-1: 2004-04, DIN EN 12100-2: 2004-04 and DIN
15112: 1975-05.
Documentation Officer:
Mohammad Achtari, Tel.: +49 (0) 7665/50207-60
This Declaration of Conformity becomes invalid if the spring
balancers are rebuilt or modified without our consent.
Bernd Lienhard
Quality Assurance Manager
Carl Stahl Kromer GmbH
Nägelseestraße 37
D-79288 Gottenheim
As the original of these Operating Instructions has been
drawn up in the German language, the German version
is legally binding. The manufacturer will accept no res-
ponsibility for translations.
Thomas Steinle
Product Manager
37
Tabla de contenido
loading

Tabla de contenido