Idiomas disponibles
Idiomas disponibles
M5450A - EXP. CARD PROFIBUS
This is a descriptive manual of the procedure to insert and
configure the inputs/outputs expansion card (relay) of the
CVMk2.
You can download the complete manual in digital format
from www.circutor.com
Before any maintenance, modification to the
connections, repair, etc., the equipment must
be disconnected from the supply and the
measure connections. If wrong operation is
suspected the equipment must remain out of service. The
equipment is designed to changed quickly in the event
of any breakdown.
1. CARD INSTALLATION
Disconnect from supply and measure the device.
Remove the screw and the cover
Insert the card in the guides.
Press the card carefully.
Put the cover and the screw.
2. CARD SELECTION
When we have introduced the card, we have to configure it.
Select
MENU
from the upper line of the display and confirm
with
SET
to unfold the window.
Select
SETUP
and confirm with
SET
move in the upper menu with the arrows since
and select it with
SET
key.
We have 3 options (
CARD 1
,
CARD 2
to select according the position which we have introduced
the card. In the picture is position 1, then we will select
CARD 1
.
NOTE: If select you select a position where is no card
NO CARD
insered, will appear the message
When we have selected the card we have to confirm with
SET
the
key and will enter in the alarm screen. (Section
2.1).
2.1. CARD CONFIgURATIONS
This card has no paramenters to configure. Only the
peripheral number (Slave ID) explained in chapter 2.3.
Going into configuration menu:
MENU--> SETUP --> EXP. CARD --> CARD X*
only will appear:
(*) Value 1, 2 or 3, depending on the card position.
2.2. CARD PARAMETERS
To visualize the parameters that CVMk2 shows refering to
the profibus communications card, you have to go to the
cards menu:
MENU --> EXP. CARD --> CARD X*.
(*) Value 1, 2 or 3, depending on the card position.
The screen shorws the paramenters:
Periph num
Bus Status
The default peripheral number is
configured by the user when the communications starts. To
configure slave ID see chapter 2.3.
The bus status shows if the bus is working or not.
2.3. COMMUNICATIONS CONFIgURATION
PROFIBUS-DP
EXPANSION
To configure the slave ID of the device whe have to use the
blue selectors of the card (Slave ID).
The selector are two to codifier the slave number in
hexagesimal code. The one HI corresponds to the HI part
of the value and the LO one, corresponds to the low part
of the code.
See example of the picture:
The differents speeds that the card supports are:
3. LEDS
The profibus card has two LEDS that indicates the status
of the card and the communications bus.
Ehen the leds are on when something error is happening
or in the card or in the profibus bus.
All the possibilities of the LED's status are showed in the
picture below:
On
| |
Card
key. Now, we have to
Error
EXP.CARD
or
CARD 3
). We have
Off
| |
Card
.
Error
On: Led ON means error.
Off: Led OFF means works correctly
M5450A - Expansión card Profibus communications -
CARD. OK
CARD NOK
or
.
0
ACTIVE
INACTIVE.
/
0
but it will change to the
| |
| |
Card
Bus
Bus
Error
Error
Line
HI
LO
8
8
SELECTOR HI = 1
SELECTOR LO
=
E
HEXADECIMAL 1E = DECIMAL 30
- 19,2 kbs
- 1500 kbs
- 93,75 kbs
- 3000 kbs
- 187,5 kbs
- 6000 kbs
- 500
kbs
- 12000 kbs
On
Off
On
| |
| |
Card
Bus
Error
Error
On
Off
Off
| |
| |
Card
Bus
Error
Error
4. CONECTOR PROFIBUS DP
The DB-9 connector hase the followin configuration:
1. Shield.
2. -.
3. "B" Non inverting input/output signal from profibus.
4. -.
5. "M5" GND. Data reference potencial.
6. "P5" 5V supply voltage.
7. -.
8. "A" Inverting input/output signal from profibus.
9. -.
5. gSD MODULES
The GSD modules are configured as the table bellow.
The table shows the number of each module, the
parameters inside and the total size of the module.
You can download the GSD file and the
descriptive document of profibus modules
from CIRCUTOR Web page, www.circutor.
com
MOD
PARAMETERS
8
8
Single voltages ph-n
Hi
Lo
Phase currents
Slave ID
1
Phase-Phase voltages
Power Factor
Frequency
2
Power
Average values
3
Neutral values
Three-phase values
4
Energy
5
THD V / I
6
THD odd / even
7
Unbalanced / Asimetry / Flicker
8
Odd voltage harmonics (15º)
9
Odd current harmonics (15º)
10
Digital Input 1 / Analog Inputs 2
11
Digital Input 2 / Analog Inputs 3
12
Digital Input 3 / Analog Inputs 1
13
Cos φ
The limits of the Profibus protocol to charge
the GSD modules are:
- Máximum 4 modules.
- Total maximum size 244 bytes.
6. TECNICAL ASSISTANCE SERVICE
In case of failure or any operational queries, please contact
the technical service of CIRCUTOR, SA.
TECHNICAL ASSISTANCE SERVICE (TAS):
Bus
(+34) 93 745 29 00
Error
CIRCUTOR, SA. – Aftersales service.
Vial Sant Jordi s/n
08232 Viladecavalls, Barcelona.
Tel.: (+34) 93 745 29 00
Fax: (+34) 93 745 29 14
mail: [email protected]
Bus
Error
CVM k 2
ByTE
SIzE
12
12
12
52
12
4
48
48
12
8
44
24
48
48
32
32
64
64
44
44
72
72
72
72
64
64
64
64
64
64
12
12
M98223801-20-10B
