ENGLISH
This instruction manual contains important information and must be read
carefully by competent persons prior to any handling, transport, inspection
or installation of this product. Every care has been taken in the preparation
of the instructions and information; however, it is the responsibility of the
installer to ensure the system complies with relevant national and
international regulations, especially safety. The manufacturer, Soler &
Palau Sistemas de Ventilación S.L.U. accepts no responsibility for
breakages, accidents or any inconvenience caused by failure to comply
with the instructions contained in this manual.
The fans referred to in this manual have been manufactured in accordance
with rigorous quality control and International standard ISO 9001. Once the
product has been installed, this manual to be retained by the end user.
Transport and manipulation
The packaging used for this fan has been designed to support normal
transporting conditions. The fan must always be transported in its original
packaging as not doing so could deform or damage the product.The fan
must always be transported in its original packaging. Do not accept delivery
if the fan is not in its original packaging or shows clear signs of having been
damaged.
The product should be stored in a dry place in its original packaging,
protected from dust and dirt until it is installed in its final location.
Do not place heavy weights on the packed product and avoid impact
damage.
Any lifting equipment must be safe and of suitable capacity for weight and
size. Special attention may be required to ensure fan assembly does not
distort or tilt as weight distribution may vary. Never lift a product by pulling it
by the wires or terminal casing. Likewise, no pressure should be applied on
the propeller, turbine or safety grid while manipulating the product.
Important information for the safety of installers and users
Installation must be carried out by qualified persons acting in
accordance with all safety precautions applicable and as
required by law, regulations and standards in the country
applicable.
All fans are designed and manufactured in accordance with EC
Directive. Safety guard accessories are available from S&P if
required due to specific installation.
Working ambient temperature for fan equipment should not be
exceeded typically this will be within -20°C to +40°C, unless
stated otherwise.
This fan must not be used in explosive or corrosive
atmospheres.
If the fan is used in atmospheres with more than 95% relative
humidity, consult the S&P Technical Service first.
If the fan is to extract air from premises where a boiler or other
combustion appliance is installed, make sure that the room has
sufficient air intakes to assure adequate combustion.
This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision
Safety during installation
Fan equipment should be electrically isolated and locked out before
any work started
Before any installation work is started, ensure that fan equipment is correct
for application. Location for installation is solid, level, flat and suitable for
mounting fan assembly.
Fan should be located in position, and assembled with any accessory
equipment supplied, on relevant mounting, anti-vibration mountings, safety
protection guards, on a solid level base to avoid any distortion and
misalignment and with correct air direction as shown on nameplate. Fan
should then be levelled on any anti-vibration mountings. Flexible connectors
must be taught to ensure no disruption to air flow, especially on inlet to fan.
Make sure there are no loose elements near the fan. When the fan is
mounted in a duct, check that it is clean of any elements and exclusively
used for ventilation system.
For electrical connections follow the wiring diagram indicated in this
manual.
Start up
Check fan equipment name plate data is appropriate to the location
electrical supply, especially Voltage, Frequency, Phase, Amps, speed are
correct.
Check earth connections, electrical terminations and terminal box lid, with
any seals, if fitted, are correct.
In compliance with Machine Directive 89/392/EU, if the fan is accessible to
operators and is a health and safety risk, adequate protection must be
fitted, information for safety equipment, including guards, can be found in
S&P accessories catalogue.
Check all rotating parts have free, unobstructed movement.
Check there are no foreign bodies inside the fan or that can be drawn into,
or fall into fan.
Check the structure is complete and has no damage. Check installation and
area is safe and energise fan and start motor.
Check that the impeller and airflow direction is correct, and there are no
unusual vibrations.
Check current does not exceed fan equipment nameplate data.
If any of the electrical safety devices blow, the fan must be quickly
disconnected from the mains supply. The whole installation should be
carefully checked before trying to start up the fan again. After two hours of
operation, check that all fixings are tight and adjust if necessary.
Maintenance
Maintenance/repairs must be carried out by competent personnel and
in accordance with applicable International, National and Local
regulations. Fan equipment should be electrically isolated and locked
out before any work started.
Fan equipment should be regularly cleaned, frequency depending upon
service load and application, but no less than every year. Cleaning should
include all areas where dust can accumulate in the fan equipment.
Special attention should be made to any unusual sounds, vibration or
temperature. If any problems are detected the fan equipment should be
stopped immediately and cause inspected. The impeller and blades should
be regularly checked for damage that could cause imbalance in the moving
parts
Recycling
In accordance with EEC Standards and our responsibility for future
generations, we are obliged to recycle all the materials we can. Therefore,
please deposit all waste material and packaging in their corresponding
recycling containers and hand in the replaced units to the nearest handler
of this type of waste product.
To clarify any questions regarding S&P products contact your local
distributor. For its location and to obtain the EU Declaration of Conformity
certified technical data sheet and copy of this instruction manual, see our
web site www.solerpalau.com.
