Tabla de contenido
Idiomas disponibles
Idiomas disponibles
FINAL SETUP
IMPORTANT: All of the settings on the motion sensor are
also controlled through the SECUR360 app. However,
if the light loses wi-fi connection (the LED indicator
will blink blue), the motion sensor settings will control
the light until wi-fi connection is reestablished. Once
the light reconnects to wi-fi, the settings in the app will
control the light.
1. Adjust the sensitivity (SENS) switch as needed ("L",
"M", "H"). Sensitivity set too high may increase false
triggering.
2. Set the ON-TIME switch to OFF, 30 seconds, or 2
minutes (the amount of time the light will stay on
after all motion has stopped).
3. Set the ECO POWER MODE switch to ON or OFF.
See Eco Power Mode section for more information.
4. Go to the App Store
for the "Secur360" app
enclosed instruction sheet, "Connecting to your new
SECUR360 device", for more details.
5. Once step 4 is complete, open the SECUR360 app and
log into the account. Use the app to set the controls
for the light fixture.
LED Indicator
• RED + Solid: Light is warming up – Stays in this mode
until the light is ready.
• RED + flashing (1 second ON / 1 second OFF): Light
is in wi-fi connection mode.
• BLUE + flashing: Light is connecting to the internet.
• BLUE + (2 Minutes ON): Light is connected to the
internet.
• BLUE : When motion is detected, the LED will be ON
until all motion has stopped for 30 seconds.
For additional information concerning this light or the
SECUR360 app, visit www.heath-zenith.com/Secur360.
IMPORTANT CONSIDERATIONS
AVOID AIMING THE SENSOR AT:
• Below are examples of objects that might produce heat
and may cause the motion sensor to trigger:
• Pools of Water
• Dryer Vents
• Heating Vents
If you suspect that a heat source of this type is triggering
the motion sensor, reduce the sensitivity.
210451-01
or Google Play™ and search
SM
and download. See the
• Air Conditioners
• Animals
• Automobile Traffic
To see operational and troubleshooting information and videos,
• Areas where pets or traffic may trigger the motion sensor.
• Nearby large, light-colored objects reflecting light may
trigger the shut-off feature. Do not point other lights
at the motion sensor.
SEASONAL CHANGES:
The motion sensor works by sensing temperature changes
across its field of view. The closer the surrounding tem-
perature is to a person's body heat, the less sensitive the
sensor will appear. The greater the temperature difference,
the more sensitive the sensor will appear. Use the sensitiv-
ity control in the app to adjust the setting as the outside
temperature changes for the different seasons. This is a
normal part of the light sensor's operation.
"Eco Power mode" is a selectable feature within the app
designed to increase battery life by reducing certain func-
tions, such as:
• The light will not have constant access to wi-fi. The wi-fi
module in the light will only activate after a set amount
of time has passed or whenever the light is activated by
motion.
• The brightness of the light will be reduced.
• Voice activation is turned off.
• When grouped with other lights, this light will not be
turned on when other lights are activated. When this
light is activated, it will turn on other lights in the group.
This light can be reset to the original factory settings either
by using the reset button on the bottom of the sensor or
through the SECUR360 app. Note: After resetting the light,
it may take up to 5 minutes for the light to be removed
from the SECUR360 app.
• Reset Button (see Figure 4) – Use a paper clip to press
the RESET button for 15 seconds to reset the light.
For additional information concerning this light or the
SECUR360 app , visit www.heath-zenith.com/Secur360.
go to www.hzsupport.com
ECO POWER MODE
RESET BUTTON
5
Tabla de contenido
