SEVERIN KS 9878 Instrucciones De Uso página 15

Ocultar thumbs Ver también para KS 9878:
Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 34
Before you get started, please note the following:
∙ Always ensure that the correct number of washers are
used on the hinge bolts.
∙ To ensure that the door can close tightly against the
frame, take the utmost care that it is properly aligned
during re-assembly.
1.
Lower the unit carefully onto its back.
2.
Remove the two screws (7) and take off the bottom
hinge bracket (8), together with the set of washers (6)
on the hinge pin, and the spacer element (5).
3.
Remove the two screws from the angled bracket
(11) and take off the bracket together with the spacer
element and the covering panel (10).
4.
Slide the door (4) off the top hinge pin and take it off.
5.
Remove the hinge pin (2) together with the nut (1) and
washers (3) from the top hinge bracket, and fit the
entire assembly to the opposite side of the cabinet.
6.
Turn the door through 180°, and then slide it over the
re-positioned top hinge pin (2).
7.
Fit the hinge pin of the bottom hinge bracket (8) into
the door.
8.
Replace the bottom hinge bracket (8) together with the
covering panel (10), the set of washers and the spacer
element (5) to the cabinet, using the screws (7).
9.
Screw the angled bracket (11), together with the
spacer element and the covering panel (10), to the
opposite side of the unit.
10. Return the whole unit to its upright position.
Caution!
Wait at least 4 hours before re-connecting the unit to
the mains.
Cleaning and defrosting
During operation, you may notice a build-up of frost around
the integral evaporator sealed into the rear of the inside
cabinet. This layer of frost will start melting when the
compressor is not working. Through a system of hoses,
the melt-water drains into the collection tray below the
compressor, where it will be absorbed into the surrounding
air.
∙ The unit does not therefore require de-frosting, but only
proper cleaning.
∙ To enable the melt-water to drain freely, always ensure
that the channel and discharge opening in the cabinet
are free of any blockage.
∙ Any water collecting in the bottom should be removed.
∙ Always remove the plug from the wall socket before
cleaning.
∙ Do not pour water over or inside the unit.
∙ Do not use aggressive cleaning detergents or those
containing alcohol. Also, do not use electrical devices
such as steam cleaning devices for defrosting or
cleaning.
∙ For frequent cleaning we recommend the use of warm
water with some mild detergent.
∙ The cabinet should be cleaned once a month.
∙ Any accessories should be cleaned separately with soapy
water. Do not put them in a dishwasher.
∙ After cleaning, thoroughly clean all surfaces with fresh
water before wiping them completely dry. When re-
inserting the plug into the wall socket ensure that you
have dry hands.
∙ To save energy and to ensure optimum performance, the
compressor (at the rear) should be carefully cleaned at
least twice a year, with a brush or a vacuum cleaner.
Trouble-shooting
Certain typical sounds can be heard when the appliance is
switched on. These sounds are caused by:
∙ the electric
motor within
the compressor
assembly; during
compressor
start-up the sound
level will be slightly
higher for a short
time.
∙ the cooling agent flowing through the circuit.
The following table lists possible malfunctions, their
probable causes and solutions. In the event of operational
problems, check first whether a solution can be found using
this table. If the problem persists, disconnect the appliance
from the mains power and contact our Customer Service
Department.
15
Tabla de contenido
loading

Tabla de contenido