Tabla de contenido
Idiomas disponibles
Idiomas disponibles
INSTRUCTION MANUAL
DESCRIPTION OF THE PARTS:
Fig. 1
HAIR CLIPPER
1. Lower blade
2. Upper blade
3. Blade moving lever
4. Power switch (0/I)
ACCESSORIES
1. Attachment 3mm
2. Attachment 6mm
3. Attachment 9 mm
4. Attachment 12mm
5. Comb
6. Hair scissors
7. Lubricating oil
8. Brush
READ ALL INSTRUCTIONS BEFORE USING
AND SAVE THESE INSTRUCTION
IMPORTANT SAFEGUARDS
To reduce the risk of death or injury by electric
shock:
•
Unplug this appliance before cleaning.
•
Do not place or store appliance where it can
fall or be pulled into a ub or sink.
•
Do not use while bathing or in a shower.
•
Do not place in, or drop into wather or other
liquid.
•
Do not reach for an appliance that has fallen
into water. Unplug immediately.
To reduce the risk of burns, electrocution, fire,
or injury to persons:
•
Use this appliance only for its intended
use as described in this manual. Do not
use altachments not recommended by the
manufacturer.
•
This appliance should never be left
unattended when plugged in.
•
Close supervision is necessary when this
appliance is used by, on, or near children or
invalids.
•
Never operate this appliance if it has a
damaged cord or plug, it is not working
properly.
•
Keep the cord away from heated surfaces.
•
Do not pull, twist, or wrap line cord.
•
Never drop or insert any object.into.this
appliance.
•
Before use, make certain blades are aligned
properly.
•
Do not place appliance on any surface while it
is operating.
•
Do not use this appliance with a damaged or
broken comb nor with teeth missing from the
blades sa injury may occur.
•
Please send the appliance to the maintenance
shop if it is damaged. Never repair it by
yourself
•
This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities,
or lack of experience and knowledge,
unless they have been given supervision or
instruction concerning use of the appliance
by a person responsible for their safety.
•
Children should be supervised to ensure that
they do not play with the appliance.
BLADE ALIGNMENT:
see illustration no. 2.1
•
Your clipperswere carefully examined to
ensure that the blades were oiled and aligned
before leaving our factory.
•
Blades must be realigned if they have been
re moved for cleaning or replacement.
•
To realign the blades, simply match the
uper and bottom blades leeth up, point for
point. (End of top blade teeth should be
approximately 1.2mm back from bottom
blade. Compare your clipper blades with the
sketch.)
•
If blade alignment is incorrect, add a lew
drops of oil to the blades, turn clipper on for
a few moments, turn off and unplug. Loosen
screws slightly and adjust. Tighten screws
after blade is aligned.
OIL:
see illustration no. 2.2
•
To maintain your clipper in peak condition,
the blades should be oiled every few haircuts.
Do not use hair oil, grease, oil mixed with
kerosene ore any solvent. As the solvent will
evaporale and leave the thick oil which may
down the blades motion.
BLADE LEVER:
see illustration no. 2.3
•
The lever conveniently located near your
thumb (if you are right-handed) so it can
easily be adjusted while the clipper is in your
hand.
•
The lever adds versatility to your clipper
by allowing you to gradually change the
closeness of your cut without an attachment
comb.
•
When the lever is in the uppermost position,
the blades will give you the closest cut and
leave the hair very short. Pushing the lever
downward gradually increases the cutting
length.
2
•
In ist lowest position, the lever will leave the
hair approximately the same length as a #1
comb.
•
The lever will also extend the use of your
blades since a different cutting edge is used in
each setting.
•
In addition, if extremely heavy hair cutting has
jammed the blades, it will help you remove
hair that has become wedged between the
two blades without removing the blades.
•
While the clipper is running, rapidly move the
lever from »close cut« to »longer cut« a couple
of times. Doing this each time after you have
finished using your clipper will help to keep
the blades clear of cut hair. If your clipper
stops cutting and this does not help, your
cutting blades are dulled. Replace them with
new blades.
INSTRUCTIONS FOR HAIR CUTTING
Before starting the hair cut:
1. Inspect the clipper, making sure that it is free
of oil between the cutting blade teeth and
turn the unit on to distribute the oil and to
make sure it is running smoothly. Wipe off any
excess oil This should be done after each use.
While using the unit, untwist the cord from
time to avoid tangling.
2. Seat the person so their head is approximately
at your eye level. This allows ease of visibility
while cutting and a relaxed control of the unit.
3. Before cutting always first comb the hair so it
is tangle free as it is naturally worn.
4. Place a towel around the neck and shoulders
of the person having the haircut.
REMINDERS
•
Cut the hair in a relaxed and slow manner. Use
short strokes only to work gradually over the
entire head.
•
Always take off a little hair at time, you can
always trim off additionat hair later.
•
As you work, comb the hair frequently back
into the style to which you are cutting.
•
When cutting with this hair clipper it is better
to leave the hair dry, not wet. With the hair
dry, it is much easier to control the amount of
hair, being cut.
BEGINNING THE HAIRCUT
Cutting hair requires practice so it is always better
to leave the hair longer for the first few haircuts
until you become used to the length to which
each comb attachment cuts the hair.
ATTACHMENT COMB (see illustration no. 3)
•
Attachment Comb #1 leaves 3mm length.
•
Attachment Comb #2 leaves 6mm length.
•
Attachment Comb #3 leaves 9mm length.
•
Attachment Comb #4 leaves 12mm length.
Each como attachment is marked accordingly on
its outside middle surface.
•
To attach a comb, hold it with its teeth
upward and slide it onto and along the clipper
blade unlit the front of the comb limaty seals
against the clipper blade.
•
To remove the comb, simply pull the comb
attachment cutter to cut its way throught
the hair. Do not force it through quickly. Also
remember to comb the hair frequently to
remove trimmed hair and to check foruneven
strands.
STEP 1– NAPE OF THE NECK:
see illustration no. 4
1. Attach comb attachment 3mm or 6mm.
2. Hold the clipper cutting edge pointed up and
begin the haircut, starting at the centre of the
head at the base of the neck (see diagram 4.1).
3. Hold the clipper comfortably in your hand
and hold lightly against the haed with the
comb teeth pointing upward. Gradually and
slowly lift the clipper, working upwards and
out wards, throught the hair, trimming just a
little at a time.
4. As you cut, gradually lift the hair clipper head
towards you. Continue to cut the back area
from the bottom of the neck upwards to the
top of the ears.
STEP 2 – BACK OF THE HEAD
Change to the next longest comb attachment
9mm or 12mm and cut the back of the head (see
diagram 4.2).
STEP 3 – SIDE OF THE HEAD
Change to one of the shorter combs 3mm or
6mm, trim sideburns, i.e. the hair directly in front
of the ears. Then change to one of the longer
combs, 9mm or 12mm, and continue to cut to the
top of the head (see diagram 4.3).
3
Tabla de contenido
