Instructions For Assembly; List Of Spare Parts - Kettler GIRO-GT 07638-500 Instrucciones

■ After your training by all means turn the turning handle for bra-
ke adjustment back to zero position in order to avoid heat in-
fluences on brake linings and disk flywheel.
■ The equipment is dependent of revolutions per minute.
■ Please ensure that liquids or perspiration never enter the ma-
chine or the electronics.
■ Before use, always check all screws and plug-in connections as
well as respective safety devices fit correctly.

Instructions for Assembly

■ Ensure that you have received all the parts required (see check
list) and that they are undamaged. Should you have any cause
for complaint, please contact your KETTLER dealer.
■ Before assembling the equipment, study the drawings careful-
ly and carry out the operations in the order shown by the dia-
grams. The correct sequence is given in capital letters.
■ The equipment must be assembled with due care by an adult
person. If in doubt call upon the help of a second person, if
possible technically talented.
■ Please note that there is always a danger of injury when work-
ing with tools or doing manual work. Therefore please be care-
ful when assembling this machine.
■ Ensure that your working area is free of possible sources of
danger, for example don't leave any tools lying around. Al-
ways dispose packaging material in such a way that it may
not cause any danger. There is always a risk of suffocation if
children play with plastic bags!
List of spare parts page 26-27
When ordering spare parts, always state the full article number,
spare-partnumber, the quantity required and the S/N of the pro-
duct (see handling).
Example order: Art.no.07638-500 / spare-part no. 68008004
/ 1 pieces / S/N ....................
Please keep original packaging of this article, so that it may be
used for transport at a later date, if necessary.
Goods may only be returned after prior arrangement and in (in-
ternal) packaging, which is safe for transportation, in the original
box if possible.
It is important to provide a detailed defect description / damage
report!
Important: spare part prices do not include fastening material; if
fastening material (bolts, nuts, washers etc.) is required, this
should be clearly stated on the order by adding the words „with
fastening material".
■ The brake linings should also be checked at regular intervals
and adjusted as necessary.
■ Always wear suitable shoes when using.
■ Nobody may be in the moving range of a training person du-
ring training .
■ Important: The Spintrainer has no safety freewheeling device.
Please see instructions on how to work the emergency brake
system.
■ The fastening material required for each assembly step is
shown in the diagram inset. Use the fastening material exact-
ly as instructed. The required tools are supplied with the equip-
ment.
■ Bolt all the parts together loosely at first, and check that they
have been assembled correctly. Tighten the locknuts by hand
until resistance is felt, then use spanner to finally tighten nuts
completely against resistance (locking device). Then check that
all screw connections have been tightened firmly. Attention:
once locknuts have been unscrewed they no longer function
correctly (the locking device is destroyed), and must be re-
placed.
■ For technical reasons, we reserve the right to carry out pre-
liminary assembly work (e.g. addition of tubing plugs).
Waste Disposal
KETTLER products are recyclable. At the end of its useful life plea-
se dispose of this article correctly and safely (local refuse sites).
KETTLER Ltd.
KETTLER House, Merse Road • North Moons Moat •
Redditch, Worcestershire • B 98 9 HL • Great Britain
Tel: +44 1527 591901 • Fax: +44 1527 62423 •
e-mail: [email protected] • www.kettler.co.uk
KETTLER International Inc.
1355 London Bridge Road • VA, Virginia Beach 23453 • USA •
Phone: +1 888 253 8853 • Fax: +1 888 222 9333 •
http://www.kettlerusa.com
5