Endress+Hauser Liquisys M COM223 Manual De Instrucciones página 121

Liquisys M COM223/253
CALIBRATION
C
Read:
Edit:
Code 22 any code
MEAS. VAL. DISPLAY
with
TEMPERATURE
DISPLAY
in °C
Edit: Read:
Code 22
any code
SETUP 1
A
SETUP 2
B
CURRENT INPUT
Z
CURRENT OUTPUT
O
ALARM
F
CHECK
P
Endress+Hauser
Entry of
calibration value
Ref = entry of
reference value current value
C1 (3) C131
Start
calibration
Countdown
600 s --> 0 s
H O = water
2
C1 (2)
C121
Start
calibration
Countdown
600 s --> 0 s
on air
C111
C1 (1)
Temperature display
in °F
1st error is displayed
(if present)
Selection of Selection of
operating mode display unit
mg/l % SAT hPa mg/l ppm ppb
A1
Entry of Entry of
salt concentration process temperature
current meas. value
0.0 % 0.0 ... 4.0 % -10.0 ... 60.0 °C
B1
Controller switch-off
Delay for controller
by current input
switch-off by current
input
Off; Input
0 s 0 ... 2000 s
Z1
Selection of Select meas. unit for
current output 2nd current output
°C; mg/l; % Sat,
Out 1, Out 2 hPa; Contr
O1
Selection of Selection of
contact type alarm delay unit
Latch=latching min; s
Momen=momentary
F1
Selection of Alarm delay
alarm threshold
0 min (s)
monitoring
0 ... 2000 min (s)
Off; Low; High;
Lo (depends on F2)
+Hi=low and high
P1
Slope is Calibration status
displayed is displayed
100.0 %
75.0 ... 140.0 % o.k.
C132
Store calibration
Calibration status
results
is displayed
yes; no; new
o.k. Exxx
C122
Calibration status Store calibration
is displayed results
o.k. Exxx yes; no; new
C112
Measured value
Temperature display
in mg/l
suppressed
Other errors are
displayed
(up to max. 10 errors)
Entry of
Automatic
altitude
pressure
compensation
0 m 0 ... 4000 m
Off; On
A2 A3
Display of
temp. difference
(Offset)
current offset
-5.0 ... +5.0 °C
B2 B3
Delay for controller Switch-off limit value
switch-on by current for current input
input
0 s 0 ... 2000 s
50% 0 ... 100%
Z2 Z3
Selection of
table option
read
Tab = Table
O3 (3)
Entry of
simulation value
current value
0 ... 22.00 mA
sim = Simulation
O3 (2)
Selection of
current range
4-20 mA; 0-20 mA
lin = linear
O2
O3 (1)
Alarm delay
Setting of
error current
0 min (s)
0 ... 2000 min (s)
22 mA; 2.4 mA
(depends on F2)
F2 F3
Setting of lower Setting of upper
alarm threshold alarm threshold
0.00 mg/l; 0...59 mg/l 20.00 mg/l; 1...60 mg/l
0.0%SAT; 0...590%SAT 200.0% ;10...600%
SAT
0 hPa; 0...1180 hPa 400 hPa; 20...1200hPa
P2 P3
Store calibration
results
Exxx yes; no; new
C133 C134
Operating matrix
WX/WS with COS31
C123
C113
Measured value
in % Sat
Entry of measured
value damping
1 (no damping)
1 ... 60
A4 * A5
Switch-off direction
for current input
Low High
Z4 Z5
Enter number of
value pairs in table
edit 1 1 ... 10
O331 O332
O321
Enter 0/4mA value
0.00 mg/l; 0...60 mg/l
0.0%Sat; 0...600% Sat
0 hPa; 0...1200 hPa
0.0 °C; -10...60 °C
O312
O311
Selection of
error numberl
1 1 ... 255
F4 F5
Selection of process monitoring
off; AC; CC monitoring
limit (AC):
SAT
AC+CC ±0.1 mg/l ±1 % SAT
±2 hPa (in 1 h)
P4
Anexo
P5
A0027490-ES
121