Stanley SW25 Instrucciones Originales página 23

ADJUSTMENT INFORMATION (Fig. C)
f Adjusting the spray nozzle (for models with this
feature) Water flow is adjusted by regulating the nozzle (2).
f Adjusting the detergent To deliver detergent at the
correct pressure, set the nozzle (2) on "
the detergent tank (12) as shown. The quantity of
detergent delivered is adjusted using the regulator (13).
f Adjusting the working pressure (on models with this
feature) The regulator (17) is used to adjust the working
pressure. The pressure is shown on the pressure gauge.
USE OF THE APPLIANCE (Fig. D)
CONTROLS
Starter device (15)
Set the starter switch on (ON/I) to:
a. Start the motor (In models without TSS device);
b. Set the motor ready to start (In models with TSS device).
If there is a pilot light on the starter device, it should light up.
Set the starter device switch on (OFF/0) to stop the appliance.
If there is a pilot light on the starter device, it should go out.
f Water jet control lever (20).
Warning! During operation the appliance must be
positioned as shown in Fig. D on a firm, stable surface.
Start-up (see Fig. D)
1. Turn on the water supply tap fully.
2. Release the safety catch (21).
3. Depress the gun trigger for a few seconds and start
up the appliance using the starter device (ON/I).
Warning! Before starting up the appliance check that it
is receiving water correctly; use of the appliance without
water will damage it. Do not cover the ventilation grilles
when the appliance is in use.
TSS Models - In TSS models with automatic delivery flow cut-o system:
a. When the gun trigger is released, the dynamic
pressure automatically cuts out the motor;
b. When the gun trigger is depressed, the automatic
drop in pressure starts the motor and the pressure
is restored after a very slight delay;
c. If the TSS is to function correctly all gun trigger
releasing and depressing operations, must be
at least 4 - 5 seconds apart.
To prevent damage to the appliance, do not allow it to operate dry
and check that it is properly supplied with water. For models without
TSS, to prevent damage to the appliance due to an increase in water
temperature, do not cut off the jet of water for more than 5 minutes
with the appliance running.
Stopping
1. Set the starter device switch on (OFF/0).
2. Depress the gun trigger and discharge the residual
pressure inside the pipes.
3. Engage the safety catch (21).
Restarting
1. Release the safety catch (21).
" or fit
2. Depress the gun trigger and discharge the residual
air inside the pipes.
3. Set the starter device on (ON/I).
Storage
1. Turn o the water supply tap.
2. Discharge the residual pressure from the gun until
all the water has come out of the appliance.
3. Switch the appliance off (OFF/0).
4. Remove the plug from the socket.
5. Drain and wash out the detergent tank at the end of
the working session. To wash out the tank, use clean
water instead of the detergent.
6. Engage the gun safety catch (21).
Refilling and using detergent
Use of a high pressure hose longer than the one originally
supplied with the appliance, or the use of an additional hose
extension, may reduce or completely halt the suction of
detergent. Fill the tank (12) with highly biodegradable detergent.
Recommended cleaning procedure
Dissolve dirt by applying the detergent mixed with water to the
surface while still dry. When dealing with vertical surfaces work
from the bottom upwards. Leave the detergent to act for 1-2 minutes
but do not allow the surface to dry. Starting from the bottom, use
the high pressure jet at a minimum distance of 30cm. Do not allow
the rinse water to run onto unwashed surfaces. In some cases,
scrubbing with brushes is needed to remove dirt. High pressure is
not always the best solution for good washing results, since it may
damage some surfaces. The finest adjustable nozzle jet setting
or the rotopower nozzle should not be used on delicate or
painted parts, or on pressurised components (e.g tyres, inflation
valves, etc.). Effective washing depends on both the pressure
and volume of the water used, to the same degree.
MAINTENANCE (Fig. E)
Any maintenance operations not covered by this chapter should
be carried out by an authorized sales and service centre.
Warning! Always disconnect the plug from the power
socket before carrying out any work on the appliance.
Cleaning the nozzle
1. Disconnect the lance from the nozzle.
2. Remove any dirt deposits from the nozzle hole using
the tool (4).
Cleaning the filter
Inspect the inlet filter (6) and detergent filter (if fitted)
ENGLISH • 23