Idiomas disponibles
Idiomas disponibles
Measure distance "B" above the jambs. Subtract
11
1/32" (1 mm) from "B" and cut the top track.
B
Length = B - 1/32" (1 mm)
Install the outside panel.
16
Outside Panel
Guide
Apply tape to the handle. Install the handle to
21
the center of the door panel. The handle must
face in on inside panels and out on outside
panels.
Handle
Troubleshooting
Symptom: Alignment
Recommended Action
1. Top of door panel is tilted away from the wall.
A. Remove the door panel from the top track and lower the roller that is closest to the wall. See step 18.
2. Bottom of door panel is tilted away from the
A. Remove the door panel from the top track and raise the roller that is closest to the wall. See step 18.
wall.
3. Door panel does not touch bumper.
A. Determine whether door panel top or bottom is closer to the wall, and then adjust the roller closest to the wall.
Symptom: Alignment
Recommened Action
1. Miscut or skewed cut bottom track.
A. Position the end cap over the skewed or miscut end of the bottom track and seal. See step 22.
Symptom: Water Leaks
Recommended Action
1. Water leak between panels.
A. When showering, make sure the inside panel is against the showerhead wall.
2. Water leak between the wall jamb and door
A. Adjust the door panel to line up with the wall jamb.
panel.
3. Water leak under the bottom track.
A. Check for proper silicone sealant application. See steps 22, 23, and 24. Apply more silicone sealant in leak location.
Symptom: Operation (open/close)
Recommended Action
1. Outside panel is difficult to move.
A. Ensure a gap exists between the bottom track and the door panel. If there is no gap, lower the rollers in the slots.
B. Ensure the panel is properly engaged over the bottom track. See step 16 and 18.
C. Ensure the rollers are properly installed. See step 18.
D. Clean any debris in the top track groove.
2. Inside panel difficult to move.
A. Ensure a gap exists between the bottom track and the door panel. If there is no gap, lower the rollers in the slots.
B. Ensure the rollers are properly installed. See step 18.
C. Clean any debris in the top track groove.
1166704-2-C
Position the top track over the wall jambs.
12
Reversible
Position the inside panel closest to the
17
showerhead. Verify alignment.
Inside Panel
Seal between the bottom track and the wall
22
jambs. If desired, install the end caps to cover
gaps or uneven cuts in the bottom track.
End
End
Cap
Cap
Assemble the inside panel rollers.
13
Sleeve
#8-32 x 3/8"
Rough/Pattern Side
(Outside of Shower)
Align the door panels by positioning the rollers
18
in the middle of the slot, and then adjust as
needed.
Lower Glass
Raise Glass
Roller
Seal outside along the wall jambs and the bottom
23
track. Tape the bottom track in position after
sealing. Seal around the top track and the wall.
2
Assemble the outside panel rollers.
14
Sleeve
#8-32 x 3/8"
Rough/Pattern Side
(Outside of Shower)
Mark the center of the door on the outside panel.
19
Apply tape to the brackets. Press the brackets
into place at the marks.
Tape
Seal inside along the wall jambs and where they
24
meet the bottom track.
STERLING® Warranty – Bath and Shower Doors
5-Years Limited
SP2375 5100 Series 5300 Series 5400 Series 6300 Series 6500 Series
3-Years Limited
1500 Series 1900 Series 2200 Series 4600 Series 4700 Series 4800 Series 4900 Series 5900 Series
1-Year Limited
500 Series 600 Series 660 Series 670 Series 690 Series 950 Series 2300 Series 3100 Series
Based on the classification specified above, STERLING bath and shower doors are warranted to be free of
manufacturing defects within the time of the specified model's limited warranty from date of sale.
Kohler Co. will, at its election, repair, rectify or replace a fixture when inspection by Kohler Co. discloses any such
defects occurring in normal usage within the time period of coverage stated above. Kohler Co. is not responsible
for removal or installation costs where replacement is indicated. Damages due to improper handling, installation or
maintenance are not considered manufacturing defects and are not covered by this warranty. This warranty is valid
for the original, consumer purchaser only.
To obtain warranty service, contact Sterling, either through your plumbing contractor, home center, wholesaler or
dealer, or by calling or writing Sterling, Consumer Services, 444 Highland Drive, Kohler, Wisconsin 53044, 1-800-
783-7546.
TO THE EXTENT PERMITTED BY LAW, ALL IMPLIED WARRANTIES INCLUDING THOSE OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED.
KOHLER CO. AND SELLER HEREBY DISCLAIM ANY LIABILITY FOR SPECIAL, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES. Some states/provinces do not allow limitations on how long an implied warranty
lasts, or the exclusion or limitation of special, incidental or consequential damages, so these limitations and
exclusions may not apply to you. This warranty gives you specific legal rights. You may have other rights which
vary from state/province to state/province.
This is the exclusive written warranty for Kohler Co.
Install the inside panel.
15
Inside
Panel
Attach the towel bar to the brackets. For two-
20
piece bars, slide the bar sections together.
# 8-18 x 3/8"
# 8-18 x 3/8"
©2014 Kohler Co.
