Tabla de contenido
Operating Instructions
Operating The Tool
(Continued)
3. After adding oil, run
tool briefly. Wipe off
any excess oil from
the cap exhaust.
RECOMMENDED HOOKUP
The illustration below shows the
recommended hookup for the tool.
1. The air com-
pressor must be
able to main-
tain a mini-
mum of
60 psi when
the tool is being used. An inade-
quate air supply can cause a loss of
power and inconsistent driving.
2. An oiler can be used
to provide oil circula-
tion through the tool.
A filter can be used
to remove liquid and
solid impurities which
can rust or "gum up" internal parts
of the tool.
3. Use 3/8" air
150 PSI WP
hoses with a
minimum
working pres-
sure of 150
psi. Use 1/2" air hoses for 50' run or
longer. For better performance,
install a 3/8" quick plug (1/4" NPT
threads) with an inside diameter of
.315" (8mm) on the tool and a 3/8"
quick coupler on the air hose.
4. Use a pressure
regulator on the
compressor, with
an operating
pressure of 0 -125
psi. A pressure regulator is required
to control the operating pressure of
the tool between 60 and 100 psi.
www.chpower.com
FULL SEQUENTIAL ACTUATION
MECHANISM
The SB3232 is equipped with a full
sequential actuation mechanism. A fas-
tener will be driven when the operator
depresses the work contact element
against the work surface and then pulls
the trigger.
After that fastener is driven, the tool
can be reset to drive another fastener
by releasing trigger and removing the
work contact element from work sur-
face in any order.
CHECKING THE WORK CONTACT
60 psi
ELEMENT (WCE)
Min.
CAUTION
!
100 psi
Contact Element (WCE) trip mechanism
Max.
before each use. The WCE must move
freely without binding through its
entire travel distance. The WCE spring
must return the WCE to its fully extend-
ed position after being depressed. Do
not operate the tool if the WCE trip
mechanism is not operating properly.
Personal injury may occur.
1. Disconnect the
air supply from
the tool.
2. Remove all fas-
teners from the
magazine. (See
"Loading/
3/8" I.D.
Unloading the Tool" section.)
3. Make sure the trig-
ger and Work
Contact Element
(WCE) move freely
up and down with-
out sticking or binding.
4. Reconnect air
supply to the
tool.
5. Depress the Work
Contact Element
(WCE) against the
work surface with-
out pulling the trigger. The tool
MUST NOT OPERATE. Do not use
the tool if it operates without
6. Remove tool from
7. Depress the
Check the opera-
tion of the Work
LOADING/UNLOADING THE TOOL
1. Always connect the tool to the air
2. Push down
3a. For nails, insert a
3b. For staples, load a clip of staples
movement
4. Push the maga-
4
Model SB3232
pulling the trigger. Personal injury
may result.
the work surface.
The Work Contact
Element (WCE) must
return to its original
down position. Pull the trigger. The
tool MUST NOT OPERATE. Do not
use the tool if it operates. Personal
injury may result.
Work Contact
Element (WCE)
against the
work surface. Pull the trigger. The
tool MUST OPERATE.
supply before loading fasteners.
on the latch
button. Pull
back on the
magazine
cover.
stick of Campbell
Hausfeld nails or
equivalent (see
"Fasteners" section) into the maga-
zine. Make sure the pointed ends
of the fasteners are resting on the
bottom ledge of the magazine
when loading. Make sure the nails
are not dirty or damaged.
with the crowns straddling the mag-
azine rail.
Magazine rail
zine cover for-
ward until latch
button pops up.
Latch
Button
Tabla de contenido
