Troubleshooting - Electrolux PRECISION Brushroll Clean Guia Del Propietario

TROUBLESHOOTING

For your safety, turn vacuum cleaner off and unplug power cord before
attempting to resolve problems.
PROBLEM
Motor will not start or suddenly stops
No suction. Vacuum cleaner does not pick
up lint or dirt
Dust cup will not lock into vacuum cleaner
Quick Release handle will not lock into
vacuum cleaner
Red "check brush roll" indicator light is on
$TWUJTQNN %NGCP YKNN PQV YQTM YJGP RGFCN
is engaged
Brushroll will not turn
Note: Any servicing of the vacuum other than described in this manual shall only be performed by an authorized service representative.
POSSIBLE CAUSES
Unit not connected to power source
Switch not turned on
Themal cut-off has operated
Blockage in air path
Dust cup full
Dust Cup Filter clogged
Hepa Filter clogged
Dust Cup Filter not in place
Switch not on proper setting
* Turbo nozzle clogged (selected models only)
Dust Cup Filter not in place
Telescopic wand is extended
1DLGEV ECWIJV KP DTWUJ TQNN
Brush roll not positioned properly
Brush roll not operating properly
Note: "Check brush roll" indicator light turns
on when brush roll is not turning. Brush roll
motor will shut off to prevent damage to motor.
If used for more than 20 seconds consecutively or
concurrently within a short period, ShearClean will
need approximately 1 minute to reset
Using brushroll clean pedal on high pile rug/carpet
SOLUTION
Push plug securely into outlet
Try another outlet or check circuit breaker
Check plug and cord for damage
2TGUU RQYGT UYKVEJ VQ ECTRGV QT DCTG QQT UGVVKPI
Correct the cause of motor overheating. See thermal cut-off information
4GOQXG CP[ QDUVTWEVKQPU VJCV TGUVTKEV CKT QY VJTQWIJ JQUG CPF XCNXG
clean out areas #1 & #2
Empty dust cup
4GOQXG CPF ENGCP NVGT
(KPG FWUV ECP DNQEM VJG CKT QY VJTQWIJ VJG NVGT CPF TGFWEG UWEVKQP GXGP
if dust cup does not look full
4GOQXG CPF ENGCP NVGT
(KNVGT OWUV DG KP NVGT HTCOG HQT EQTTGEV RGTHQTOCPEG
/CMG UWTG NVGT HTCOG KU KPUVCNNGF RTQRGTN[ KP NVGT EQXGT HQT FWUV EWR CU-
UGODN[ VQ V DCEM KPVQ RNCEG
7UG ECTRGV UGVVKPI HQT ECTRGVVGF QQTU
7UG DCTG QQT UGVVKPI HQT JCTFUWTHCEGF QQTU CPF YJGP WUKPI CEEGU-
sories
Remove and clean debris from turbo nozzle
.QECVG FWUV EWR NVGT CPF KPUGTV KPVQ FWUV EWR
Place end of wand into opening at back of vacuum and align ribs into
grooves
Unplug vacuum, remove debris and threads from brush roll. Depress
brush roll reset button, plug in unit, and continue.
7UG DCTG QQT UGVVKPI YJGP XCEWWOKPI HTKPIG QH TWIU
Check brush roll for threads and debris. Clean if needed
Make sure both ends of brush roll are free of debris and secured properly
so roll can rotate freely
&Q PQV WUG $TWUJ 4QNN %NGCP HQT QPG OKPWVG (GCVWTG UJQWNF VJGP TGVWTP
to normal function
/QXG WPKV VQ DCTG QQT RWUJ TGUGV DWVVQP 1RGTCVG PQTOCNN[