De Dietrich DHD497XE1 Instrucciones Para Instalación Y Uso página 4

L1) Les 4 témoins lumineux VERTS signalent la vitesse en cours.
L2) Quand le témoin lumineux est rouge (avec le moteur arrêté) il indique l'ALARME DES FILTRES. Quand le témoin lumineux
est vert (clignotant) il indique que le TIMER a été actionné par la touche E.
ALARME FILTRES:
Après 30h de fonctionnement le voyant L2 devient ROUGE. Il signale que les filtres à graisse doivent être nettoyés.
Après 120h de fonctionnement le voyant L2 devient ROUGE et clignote il indique que les filtres à graisse doivent être
nettoyés et les filtres à charbon remplacés.
Après avoir nettoyé les filtres à graisse (et/ou remplacé les filtres à charbon), appuyer sur la touche E pour faire redémarrer
le comptage des heures pendant la visualisation de l'alarme filtres.
Filtres à graisse: un soin particulier doit être accordé aux filtres à graisse qui doivent être nettoyés périodiquement,
quand intervient l'alarme des filtres à graisse. Pour les instructions, concernant l'alarme des filtres, voir le paragraphe
des Commandes. Démontez les filtres comme indiqué au point 1 et les laver avec un détergent neutre.
Filtres à charbon: Si l'on utilise l'appareil en version filtrante, il faut remplacer périodiquement les filtres à charbon,
quand intervient l'alarme des filtres à charbon. Pour les instructions, concernant l'alarme des filtres, voir le paragraphe
des Commandes. Démontage du filtre(s) à charbon: enlever la grille métallique (Fig.3a) et le filtre antigraisse (Fig.3b).
Retirer le filtre à charbon en poussant l'arrêt vers l'intérieur, faire pivoter le filtre jusqu'à faire retirer les deux languettes
de leurs sièges (Fig.16).
Illumination: pour accéder aux ampoules il faut enlever le support métallique en dévissant les deux vis (Fig.18) et
le déplacer vers la droite; pour changer les ampoules allogène dévisser l'embout dans le sens contraire des aiguilles
d'une montre et extraire le bulbe (Fig. 19). Remplacer avec des ampoules du même type.
ENGLISH
WARNING
The distance between the supporting surface for the cooking worktop on the hob and the lower part of the
hood must be at least 65 cm. If the instructions for installation for the hob specify a greater distance, this
has to be taken into account.
The air collected must not be conveyed into a duct used to blow off smokes from appliances fed with an
energy other than electricity (central heating systems, thermosiphons, water-heaters, etc.).
Comply with the official instructions provided by the competent authorities in merit when installing the disposal
duct. In addition, exhaust air should not be discharged into a wall cavity, unless the cavity is designed for
that purpose.
The room must be well ventilated in case a hood and some other heat equipment fed with an energy other
than electricity (gas, oil, coal heaters, etc) operate at the same time.
The intake hood could create a vacuum indeed by extracting the air out the room. The vacuum should not
exceed 0,04mbar. This prevents the head source to generate in-drawghts of gas that must be extracted out.
Check the data label inside the appliance; if the symbol (
has such technical particularities that it belongs to class II insulation, therefore it must not be earthed.
The following warning is valid in the United Kingdom only: in case your cable is not furnished with a plug,
read the following instructions; as the colours of the wires in the mains lead of this appliance may not
correspond with the coloured markings identifying the terminals in your plug, proceed as follows: – the wire
which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black;
– the wire which is coloured brown must be connected to the terminal which is marked with the letter L or
coloured red. – terminal of a three-pin plug.
Check the data label inside the appliance; if the symbol (
ATTENTION: This appliance must be earthed. When making the electrical connections, check that the current
socket has a ground connection.
The following warning is valid in the United Kingdom only: in case your cable is not furnished with a plug,
read the following instructions; as the colours of the wires in the mains lead of this appliance may not
correspond with the coloured markings identifying the terminals in your plug, proceed as follows:
– the wire which is coloured green and yellow must be connected to the terminal in the plug which is marked
with the letter E or by the earth symbol [
is coloured blue must be connected to the terminal which is marked with the letter N or coloured black; –
the wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured
red.
When making the electrical connections, check that the voltage values correspond to those indicated on the
data plate inside the appliance itself. In case your appliance is not furnished with a non separating flexible
cable and has no plug, or has not got any other device ensuring omnipolar disconnection from the electricity
main, with a contact opening distance of at least 3 mm, such separating device ensuring disconnection from
) is printed, read the following: this appliance
) is NOT printed, read the following:
], or coloured green or green and yellow; – the wire which