Maintenance And Service; Maintenance And Cleaning; After-Sales Service And Application Service - Bosch PCL 20 Manual Original

OBJ_BUCH-725-005.book Page 12 Friday, May 9, 2014 11:22 AM
12 | English
Mounting the wall mount (see figure I): For fastening to a
wall, the holding plate 15 must be folded out. Press pushbut-
tons 14 on both sides of the holding plate (a), fold the holding
plate up (b), lightly push it downward and allow it to latch (c).
For height adjustment of the measuring tool, the holding plate
15 can be moved up or down within a range of 6 cm. For this,
press the pushbuttons 14 on both sides of the holding plate,
slide the holding plate to the requested height and allow it to
latch again. The scale on the side of the wall mount aids the
height adjustment.
Fastening the wall mount (see figure J): Fasten the wall
mount 13 as vertical as possible to a wall with the holding
plate 15 folded up. Secure it safely against slipping off, e.g.,
with two fastening screws 16 (commercially available).
Screw the 1/4" screw 17 of the wall mount into the tripod
mount 8 of the measuring tool.
Using as a table stand (see figure K): In the plumb beam op-
erating mode, the visibility of the bottom plumb beam 3 can
be improved by not placing the measuring tool directly on a
surface, but by inserting it in the folded together wall mount
13.
For this, place the wall mount as horizontal as possible onto a
firm and level support. Press pushbuttons 14 at the holding
plate 15 (a). Slide the holding plate to the stop against the up-
per end of the wall mount (b). Fold the holding plate down-
ward (c). Screw the 1/4" screw 17 of the wall mount into the
tripod mount 8 of the measuring tool. Then, allow the holding
plate to latch in the wall mount.
Turn the mounted measuring tool in such a manner that the
bottom plumb beam 3 faces downward. If required, lightly
fold up the holding plate again to loosen the 1/4" screw 17 for
alignment of the measuring tool.
Laser Viewing Glasses (Accessory)
The laser viewing glasses filter out the ambient light. This
makes the red light of the laser appear brighter for the eyes.
 Do not use the laser viewing glasses as safety goggles.
The laser viewing glasses are used for improved visualisa-
tion of the laser beam, but they do not protect against laser
radiation.
 Do not use the laser viewing glasses as sun glasses or in
traffic. The laser viewing glasses do not afford complete
UV protection and reduce colour perception.

Maintenance and Service

Maintenance and Cleaning

Store and transport the measuring tool only in the supplied
protective pouch.
Keep the measuring tool clean at all times.
Do not immerse the measuring tool in water or other fluids.
Wipe off debris using a moist and soft cloth. Do not use any
cleaning agents or solvents.
Regularly clean the surfaces at the exit opening of the laser in
particular, and pay attention to any fluff or fibres.
1 609 92A 0JR | (9.5.14)
In all correspondence and spare parts orders, please always
include the 10-digit article number given on the type plate of
the measuring tool.
In case of repairs, send in the measuring tool packed in its
protective pouch 19.

After-sales Service and Application Service

Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can
also be found under:
www.bosch-pt.com
Bosch's application service team will gladly answer questions
concerning our products and their accessories.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0844) 7360109
E-Mail: [email protected]
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: (01) 4666700
Fax: (01) 4666888
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: (01300) 307044
Fax: (01300) 307045
Inside New Zealand:
Phone: (0800) 543353
Fax: (0800) 428570
Outside AU and NZ:
Phone: +61 3 95415555
www.bosch.com.au
Republic of South Africa
Customer service
Hotline: (011) 6519600
Bosch Power Tools