Initial Setup - KlipXtreme Allure KLS-660 Manual De Instrucciones

Remote control
In addition to the panel controls, a remote control is included which provides additional functions to allow
greater control over the media player.
• Install the batteries in the remote control following the correct polarity as indicated inside the compartment.
(Requires two AAA batteries).
• In order for the remote to operate properly, ensure that it is pointed toward the front of the speaker.
1
2
3
4
5
6
7
8
Control
Cancels the audio coming from the speaker. Press it again to unmute
1. Mute button
the speaker in all modes.
In USB/SD press this button briefly to play the previous track. Press and hold
TM
2.
this button to go backward fast.
In FM and Bluetooth
This feature is not available in Line In mode
Press this button to cycle through the different audio sources: FM, Bluetooth
3. Mode
USB and SD
TM
Use this button to activate the recording function when using the wired or wireless
4. REC button
microphone. Press it again to stop this function. Insert a USB or SD
the microphone prior to start recording. You can record from the external microphone,
Line in and FM input and save the recording to the storage device of your choice.
Enables the reverberation effect of the microphone. Use + or – to increase or
5. and 16. ECHO+/-button
decrease the effect.
Increases or decreases the bass (low) frequencies of the speaker.
6. Bass +/-
Scrolls through the different equalizer sound effects.
7. EQ
STANDBY
9
10
11
12
LED 13
MODE REPEAT
ON/OFF
14
REC
15
REC R.DEL
PLAY
16
17
ECHO- ECHO+ M-PRI
- -
+ +
18
BASS TREBLE
+ +
EQ
19
M.VOL VOL
- 0 -
1 2 3
20
4 5 6
7 8 9
Description
mode press it briefly to go to the previous channel or song.
®
modes.
8. Mic volume +/- button
9. STANDBY
10.
11.
12. LED ON/OFF
13. Repeat button
14. REC/Play button
15. R-DEL button
17. M-PRI
18. Treble +/- button
19. Vol +/-
20. Numbered keys (0 to 9)
IV. Initial setup
Note: For your safety, read this manual and follow all safety instructions before using the product.
Charging the battery
1. Plug the AC cable to a wall outlet.
2. When the unit is not in use or switched off, it will automatically recharge the internal battery as long as it
remains connected to utility power.
Powering on the unit
1. Turn the volume control on the top panel fully counterclockwise.
2. Connect audio input devices first. Make sure all input sources such as microphones, CD players, or digital
media players are turned off and volume settings are set to their lowest settings (zero).
3. Check that the loudspeaker voltage selector is set to the same voltage as the AC power outlet.
4. Then, connect the power cord to the loudspeaker and AC power outlet.
5. Slowly turn the volume clockwise until the sound output is at the desired level. If there is no sound, check
to make sure the source equipment is providing audio output.
V. Functionality
1. Auxiliary mode operation
Recommendation: An RCA to 3.5mm connector audio cable has to be used to enable audio playback from
devices fitted with an auxiliary 3.5mm jack.
a. First, connect one side of the RCA 3.5mm cable to the auxiliary port on the speaker and the other side of the
, Line in,
®
cable to the source of choice. If the speaker is not set to the LINE IN mode, press the MODE button to toggle
through the different modes available until the preferred mode is found: Line In, Bluetooth®, USB, SD
drive and connect
TM
b. Start streaming audio files directly from the source of choice.
2. USB mode operation
Recommendation: Use a USB memory stick to enable audio playback from compatible files stored in a USB memory stick.
a. First, connect a USB memory stick to the USB port of the speaker.
b. The speaker will detect the USB device and play the audio files. If the USB drive is not automatically
detected, press the MODE button to toggle through the different modes available until the preferred
mode is found: Line In, Bluetooth®, USB, SD
Increases or decreases the volume of the microphone.
Press this button to change the device from standby to active mode, and vice versa.
Press to start and pause media during Bluetooth®, SD
tuner mode, press it to scan for channels.
In USB/SD press this button briefly to play the next track. Press and hold this button
TM
to go forward fast.
In FM and Bluetooth mode press it briefly to go to the next channel or song.
®
This feature is not available in Line In mode
Press this button to turn the LED lights on or off.
Use it to repeat a track or song in only in USB and SD
repeat or repeat all function.
Press this button to play what was recorded in the unit.
Use it to delete the recorded files.
Use it to give priority to the microphone. The music volume will decrease
automatically when the microphone is in use.
Adjusts the level of the high-frequency range.
It increases or decreases the volume level of the speaker. The volume can also be
controlled directly from each of the sources connected to the speaker.
In USB and SD modes, press any key from 0 to 9 on the remote to choose directly
TM
the tracks you want to play.
, FM.
TM
or USB playback. In
TM
modes. It has a single
TM
, FM.
TM