Initial Operation; Commissioning, Operation; Routine Cleaning - Nilfisk-Advance SDS 424 Instucciones De Manejo

Explicit reference is made to the risks of using highly flammable, com-
bustible, toxic, health-hazardous, corrosive or irritant substances.

Initial operation

•
Delivery, instruction on safety procedures, handling and mainte-
nance and initial operation are generally carried out by our author-
ized specialist.
•
If this is not the case, the operator is responsible for instructing
machine users.
Commissioning/operation
Please remember that the voltage in the building being cleaned must
concur with that given on the machine's type plate.
Assembly instructions
•
The motor head and bar are supplied separately packed.
•
First release the hexagon socket srews in the shaft adjustment unit
(17).
•
Then feed the bar (7) gently as far as it will go into the shaft ad-
justment unit (17).
•
Align the handle bar (1) parallel with the wheels (9), so that the
open side of the housing of the top shaft element (3) is facing to
the rear.
•
Then tighten the hexagon socket screws again.
•
Wind the electric cable (18) around the handle bar (a) and cable
hook (8).
Preparations for use
•
Grasp the handle bar (1) with both hands and tip the machine until
it is resting on both wheels (A).
•
Then wheel the machine to its place of work and plug the electric
cable into the power supply.
•
Lay the accessories (11), i.e. brush or drive plate with pad, on the
floor.
•
Now tip the machine back onto the wheels and push it over the
brush (or drive plate) until the drive star and brush flange are verti-
cally aligned. Lower the machine onto the brush (B).
•
Then squeeze the shaft adjustment lever (5) and lower the bar (7)
into its working position. Both arms should be extended loosely
downwards (C).
•
Align the machine horizontally above the working element (brush
or drive plate), press the switch lock (4) and press the brush motor
switch (2) briefly.
•
The accessory automatically engages.
Machine use
•
Press the brush motor swith (2) (to the right or left). The motor
starts.
•
If you raise the bar (7) slightly, the machine moves to the right (D).
•
If you lower the bar, the machine moves to the left (D).
•
If you keep the bar in its central position, the machine works on the
spot.
After use
•
Squeeze the shaft adjustment handle (5) and shift the bar (7) into
its vertical position.
•
Then tip the machine onto its wheels (9) and press the brush
motor switch (2) briefly. The accessory (11) disengages.
•
Remove the plug from the power socket and wind the electric
cable (18) around the handle bar (1) and cable hook (8).
Thorough cleaning the easy way with the SDS 424 (190 rpm):
•
For thorough cleaning, the single-disc machine is supplied with the
following accessories:
- Liquid tank (13)
- Scrubbing brsuh (11) or drive plate with black pad (19).
•
Fasten the tank to the mounting (14).
•
Slide the outlet hose (12) onto the water connector (16).
•
Fill the tank (13). Then fit the brush or drive plate with pad.
•
Control the flow of liquid with the tank lever (15) by pulling the
lever (15) upwards.
•
Vacuum the dirty wash solution a section at a time with a water
extractor.
Shampooing thoroughly and efficiently with
SDS 424 (190 rpm)
•
For shampooing, the machine is equipped with the following ac-
cessories:
- Liquid tank; 0.3 Perlon shampooing brush or Sapur pad for textile
floorcoverings.
•
The working procedure is in principle the same as for thorough
cleaning.
•
Start the machine with the shampooing brush dry.
•
Meter a small amount of liquid until the bristles are saturated with
foam.
•
Run the machine with the rotating brush from right to left or
viceversa. ⇒ Immediately after this, run the machine in the same
way in the reverse direction, but with an overlap of about a quarter
of the strip already treated (E.)
•
Only then run the machine in a spiral pattern over the shampooed
strips. ⇒ In doing so, work both strips at the same time (F.)
•
During shampooing it is highly advisable to immediately remove
the dirt-laden foam a section at a time with a water extractor.
Assembly instructions for Spraymaster
•
Fit the holder for the spray can to the bar (7) with the holder point-
ing upwards and, when viewed from the operating side, to the left
(G).
•
Hook the spray can's tongue onto the holder, pivoting the holder
back until the ball catch engages.
•
Then slide the spring clip over the shaft adjustment unit (7).
•
Attach the box on the right or left as desired (H).
•
Point the universal-jointed hose in the desired direction.

Routine cleaning

For routine cleaning, your machine is equipped with the following
accessories:
- Spraymaster, drive plate for pads, yellow-and-brown or green
pad for Low-Speed or Spraymaster, drive plate for pads, red pad
for High Speed
GB