Setup Menu - Briteq BEAMBAR10-RGBW Manual De Instrucciones

ENGLISH
 The device should be installed out of reach of people and outside areas where
persons may walk by or be seated.
 Before rigging make sure that the installation area can hold a minimum point load of
10times the device's weight.
 Always use a certified safety cable that can hold 12times the weight of the device
when installing the unit. This secondary safety attachment should be installed in a
way that no part of the installation can drop more than 20cm if the main attachment
fails.
 The device should be well fixed; a free-swinging mounting is dangerous and may not be considered!
 Don't cover any ventilation openings as this may result in overheating.
 The operator has to make sure that the safety-relating and machine-technical installations are approved by
an expert before using them for the first time. The installations should be inspected every year by a skilled
person to be sure that safety is still optimal.

SETUP MENU

With the setup menu you can fully configure the projector. All settings are preserved when the unit is
disconnected from the mains.
Browsing the setup menu:
General instructions for setup.
 Press the [MODE] button or ↑/↓ buttons to browse the different functions of the setup menu until the
required function is shown on the display.
 Press the [ENTER] button to access the function and change its parameters.
 The cursor of the value to change starts blinking. Use ↑/↓ button to change the value.
 Press the [ENTER] button again confirm and select the next parameter to adjust.
[DMX ADDRESS]]
Used to set the desired DMX-address.
 Press the [ENTER] button As soon as the menu option is shown: the values can be changed
 Use ↑/↓ buttons to select the desired DMX512 address. The last occupied DMX-address is also shown:
makes it easier to set the address of the next unit in the chain.
 Once the correct address shows on the display, press the [ENTER] button to save it.
Note: on RDM-compatible controllers this option can also be remotely set.
[CHANNEL MODE]
Used to set the desired channel mode.
 Press the [ENTER] button As soon as the menu option is shown: the values can be changed
 Use ↑/↓ buttons to select the desired mode:
 BEAMBAR5-RGBW modes:
 03CH FX: compressed channel mode, perfect for fast setup and use.
 04CH RGB+DIM: all 5 projectors together RGB + master dim/audio/strobe channel
 04CH RGBW: all 5 projectors together RGBW
 05CH: all 5 projectors together RGBW + master dim/audio/strobe channel
 06CH: all 5 projectors together RGBW + master dim + audio/strobe channel
 05CH WW 3200K: individual projectors 0-100% with color temperature 3200K
 05CH CW 5600K: individual projectors 0-100% with color temperature 5600K
 05CH CW 10000K: individual projectors 0-100% with color temperature 10000K
 20CH: all projectors individually RGBW
 23CH: all projectors individually RGBW + 3 channels for special functions.
 25CH: all projectors individually RGBW + master dim TO BE CHECKED
 30CH: all projectors individually RGBW + master dim + strobe channel
 BEAMBAR10-RGBW modes:
 03CH FX: compressed channel mode, perfect for fast setup and use.
 04CH RGB+DIM: all 10 projectors together RGB + master dim/audio/strobe channel
 04CH RGBW: all 10 projectors together RGBW
 05CH: all 10 projectors together RGBW + master dim/audio/strobe channel
 06CH: all 10 projectors together RGB + master dim + audio/strobe channel
 10CH WW 3200K: individual projectors 0-100% with color temperature 3200K
 10CH CW 5600K: individual projectors 0-100% with color temperature 5600K
BRITEQ
®
4/86
OPERATION MANUAL
BEAMBAR5+10-RGBW