Black+Decker CUA525BH Traducción De Las Instrucciones Originales página 10

ENGLISH
J1 FLOORSENSOR Touch Button
Intelligent floor sensor technology increases suction on carpets and
switches to Economy Mode for lighter tasks, such as hard floor cleaning,
thus optimising the battery run time this feature is active when the LED
(J1a) is lit. In order to maximise runtime on all surfaces, switch this
feature off by touching area (J1).
J2 Power contol Touch Slider
Touch button panel allows you to control the level of power to the unit
from minimum to maximum by sliding finger along this area.
J3 Beater bar Touch Button
Allows you to turn the beater bar function on and off.
J4 Power indicator
Allows you to monitor the level of power being used.
J5 BATTERYSENSOR Indicator
The LED battery indicator displays the remaining charge and warns you
when the battery is low. The final LED will flash continuously when there
is only 1 minute of runtime remaining. All LEDs will flash when the unit is
discharged.
J6 FILTERSENSOR
Smart sensor technology automatically detects (the symbol will light red)
when the filter becomes clogged and needs to be cleaned.
Note: The FILTERSENSOR LED will flash and the unit will
automatically shut down when there is any obstruction in the
flexible hose or filters which is causing the motor to overheat.
Disconnect and remove the blockage immediately.
Using the handle / wand (Fig. B, C, D, E)
Press the handle / wand release button (11) to free the
u
handle / wand (3) from the chassis (12).
Free the hose connector (9) from the chassis hose port
u
(13) as shown in figure B.
Press the chassis release button (12b) to release the hand
u
held vac (5) from the chassis (12) as shown in
figure C.
Connect the hose connector (9) to the flexible tube port
u
(3a) ensuring that the latch (9a) clicks securely into place
as shown in figure D.
10
(Original instructions)
Extend the crevice tool (4) as shown in figure E, until it
u
clicks in place.
To retract the crevice tool (4) press the tube extension
u
latch (3b) allowing it to return to its normal position.
Using the 3-in-1 accessory tool (Fig. F)
The 3-in-1 handle / wand (15) has three configurations.
u
1. Brush mode.
2. Small crevice mode.
3. Upholstery mode.
The 3-in-1 handle / wand can be fitted either directly to the
u
hose connector 9 or to the extendable crevice tool (4) as
shown in figure F.
Removing and clearing the beater bars
(Fig. G, H)
To remove the beater bar cassette (14a) from the floor
u
head (14) Depress the release button (14b) as shown in
figure G.
The beater bar (18) can now be removed.
u
The end pieces are also removable allowing you to clear
the brushes from any hair or other debris that may have
accumulated as shown in figure H.
Note: If an object gets caught in the beater bar it automatically
stops. Turn the unit off, remove object and continue.
Note: The CUA525BHP unit is supplied with a specialised pet
beater bar (18a) for cleaning pet hairs etc.
Charging (Fig. I)
Place the appliance into the charging base (7) as shown in
u
figure I .
Plug the charging base (7) into an electrical outlet.
u
Switch the electrical outlet on. The LED charging indicator
u
will flash and increase in sections.
LEDs go out when fully charged.
The appliance must be charged for 6 hours.
u
Note: The Charging base is supplied with 2 screws and wall
plugs for securing it to a wall, providing extra stability, as
shown in figure I.
Battery Sensor LED Patterns
Battery diagnostics
If the appliance detects a weak battery, the charging indicator
will flash at a fast rate when the power button is activated.
Proceed as follows:
Plug in the charger. Switch on at the mains.
u
Leave the appliance to charge.
u
Battery Fault (All LEDs)
Charger Fault (All LEDs)
Battery Hot (All LEDs)