Alemite 596-A Guía De Servicio página 7

Cordless Grease Gun
1. Pull the follower rod and engage the follower by
rotating the rod.
2. Depress Bleed Valve (32) and at the same time push on
the follower rod.
Once the air is eliminated, operate the gun several times.
Once grease appears, disengage the follower rod from the
follower and push into the Grease Cylinder.
Check Valve Contamination
Should the gun fail to prime; the outlet check may be
held open. Remove Plug (44), clean Ball (41), and the Ball
seat of Head (21).
Gun Operation
Battery (39) is intentionally shipped with a low charge.
Charge the Battery prior to use.
• Refer to the Battery Charger Operation section for
details.
CAUTION
The gun is equipped with software to protect the
motor. When a blocked bearing, line, or grease
fitting causes the gun to stall, the software
will cut power to the motor and the LCD will
illuminate with solid red LED backlight. If this
situation occurs, release the trigger immediately.
For maximum motor life, avoid operating at stall.
Speed Selection
The gun is equipped
with a two speed electronic
transmission to provide a high
and low flow rate, refer to
Specifications for performance
at each speed. The gun is in
high speed when "2" is shown
on the slide switch, see figure
for illustration. Maximum
pressure can be achieved in
both High (2) and Low Speed (1).
LCD Functions
The Liquid Crystal Display features an electronic grease
meter, grease level gauge, and battery level indicator. To turn
the LCD ON, tap the reset button one time.
To enter reset mode, press and hold the reset button. After
2 seconds the digits of the grease meter begin to flash, unit of
measure (oz/g).
Releasing the reset button when grease meter digits is
flashing will reset the meter to zero, releasing the button while
the grease cylinder level segments are flashing will restore
the gauge to full, and releasing the button while the unit of
measure is flashing will change unit of measure.
Alemite LLC
To order call 1-800-548-1191 or visit www.partdeal.com - [email protected]
Stall Indication
During stall condition (in the case of a clogged fitting or
line) the gun will stop pumping grease and the LCD display
will be illuminated with Red backlight. If this condition
occurs, release trigger immediately. Inspect, clean, and/or fix
the grease passage before trying to dispense grease into the
system.
Loss of Prime Indication
Loss of prime occurs when there is an air pocket in the grease
or when the grease cylinder is empty. When this occurs the
LCD screen will flash Red to indicate that the gun is not
pumping grease. During loss of prime the grease meter does
not count empty piston strokes.
Flashlight
To turn the flashlight ON, tap the reset button one time. If
the LCD screen is not already ON, two taps of the reset button
would be required to turn the flashlight ON.
To turn the flashlight OFF, simply tap the reset button
one time. The flashlight will automatically turn OFF after 20
seconds unless the trigger is operated to dispense grease. If
trigger is pressed to operate the gun, the light will remain ON
until 20 seconds after the trigger is released.
Battery and Charger Safety Rules
This manual contains important safety and operating
instructions for Battery part number 343291 and Battery
Chargers 343290 and 343299.
WARNING
Before using the Battery Charger read all
instructions and cautionary markings on Battery
Charger (54), Battery (39), and products using the
Battery.
An extension cord should not be used unless
absolutely necessary. Use of an improper
extension cord could result in a risk of fire and
electric shock. If an extension cord must be
used, make sure it is 18- gauge. Check to ensure
that the pins on the plug of the extension cord
are the same number, size, and shape as those
of the plug on the Charger. Make sure that the
extension cord is properly wired and in good
electrical condition.
Do not incinerate the Battery, even if it is severely
damaged or completely worn out. The Battery
may explode in fire.
7
(Original Instructions) SER 596-A
Revision (7-14)