PROBLEM
Burners burn with a yellow or orange flame, in
conjunction with the smell of gas (This is normal
for the burner lighting tube).
Symptoms:
Burners do not light. -or- Burners have a small
flickering flame in the "HI" position. -or-
Barbecue temperature only reaches 250˚ to 300˚
in the "HI" position.
Burner does not light, or flame is low in "HI"
position.
Experiencing flare-ups:
CAUTION: Do not line the bottom tray
with aluminum foil.
Burner flame pattern is erratic. Flame is low when
burner is on "HI". Flames do not run the whole
length of the burner tube.
Inside of lid appears to be "peeling." (Resembles
paint peeling.)
Cabinet doors are not aligned.
If problems cannot be corrected by using these methods, please contact the Customer Service Representative in your area using the contact information on our web
site. Log onto www.weber.com
®
.
PROBLEM
Side Burner does not light.
Flame is low in "HI" position.
Push button ignition does not work.
If problems cannot be corrected by using these methods, please contact the Customer Service Representative in your area using the contact information on our
web site. Log onto www.weber.com
WWW.WEBER.COM
®
TROUBLESHOOTING
Inspect Spider/Insect Screens for possible obstructions.
(Blockage of holes.)
The excess flow safety device, which is part of the
barbecue to cylinder connection, may have activated.
Is LP fuel low or empty?
Is fuel hose bent or kinked?
Does Burner light with a match?
Did you use the snap igniter several times until the main
burner lit (See Lighting Instructions)?
Does the igniter work (Do you see a spark when you
repeatedly use the snap igniter?
Are you preheating barbecue in the prescribed manner?
Are the cooking grates and Flavorizer
coated with burned-on grease?
Is the bottom tray "dirty" and not allowing grease to flow
into catch pan?
Are burners clean?
The lid is porcelain enamel or stainless steel, not paint. It
cannot "peel". What you are seeing is baked on grease
that has turned to carbon and is flaking off.
THIS IS NOT A DEFECT.
Check the adjustment pin on the bottom of each door.
SIDEBURNER TROUBLESHOOTING
CHECK
Is gas supply off?
The excess flow safety device, which is part
of the barbecue to cylinder connection, may
have activated.
Is the fuel hose bent or kinked?
Does burner light with a match?
®
.
CHECK
Clean Spider/Insect Screens. (See Section "Annual
Maintenance")
To reset the excess flow safety device turn all burner control
knobs and the cylinder valve off. Disconnect the regulator
from the cylinder. Turn burner control knobs to "HI". Wait
at least 1 minute. Turn burner control knobs to "OFF".
Reconnect the regulator to the cylinder. Turn cylinder valve
on slowly. Refer to "Lighting Instructions".
Refill LP cylinder.
Straighten fuel hose.
If you can light Burner with a match, then check the
Crossover
Make sure to hold the control knob in for two seconds after
snapping the igniter and seeing the orange flame from the
burner lighting tube.
Try manually lighting the burner (refer to "Main Burner
Manual Lighting"). Call customer service.
All burners on HI for 10 to 15 minutes for preheating.
®
bars heavily
Clean thoroughly. (See Section "Cleaning")
Clean bottom tray.
Clean burners. (See Section "Maintenance".)
Clean thoroughly. (See Section "Cleaning".)
Loosen adjustment nut/s. Slide door/s until aligned. Tighten
nut.
Turn supply on.
To reset the excess flow safety device turn all burner control knobs and the cylinder
valve off. Disconnect the regulator from the cylinder. Turn burner control knobs to
START/HI. Wait at least 1 minute. Turn burner control knobs to "OFF". Reconnect
the regulator to the cylinder. Turn cylinder valve on slowly. Refer to "Lighting
Instructions".
Straighten hose.
If match lights burner, check igniter (see Sideburner Maintenance).
31
CURE
®
ignition system.
CURE
31