Tabla de contenido
Idiomas disponibles
Idiomas disponibles
English
3. Charging is complete when the red charging light
remains continuously ON. Battery pack can be left in
charger or removed. Some chargers require the battery
pack release button to be pressed for removal.
4. Charger will not charge a faulty battery pack, which
may be indicated by the light staying OFF. Take charger
and battery pack to an authorized service center if light
stays OFF.
nOTE: Refer to label near charging light on charger
for blink patterns. Older chargers may have additional
information and/or may not have a yellow indicator light.
hot/Cold Pack Delay
When the charger detects a battery pack that is too hot
or too cold, it automatically starts a Hot/Cold Pack Delay,
suspending charging until the battery pack has reached an
appropriate temperature. The charger then automatically
switches to the pack charging mode. This feature ensures
maximum battery pack life.
A cold battery pack may charge at a slower rate than a warm
battery pack.
The hot/cold pack delay will be indicated by the red light
continuing to blink but with the yellow light continuously
ON. Once the battery pack has reached an appropriate
temperature, the yellow light will turn OFF and the charger
will resume the charging procedure.
DCB118 and DCB1112 Chargers
The DCB118 and DCB1112 chargers are equipped with
an internal fan designed to cool the battery pack. The fan
will turn on automatically when the battery pack needs to
be cooled.
Electronic Protection System
Li‑Ion tools are designed with an Electronic Protection
System that will protect the battery pack against overloading,
overheating or deep discharge. The tool will automatically
turn off and the battery pack will need to be recharged.
Important Charging Notes
1. The charger and battery pack may become warm to the
touch while charging. This is a normal condition, and
does not indicate a problem. To facilitate the cooling of
the battery pack after use, avoid placing the charger or
battery pack in a warm environment such as in a metal
shed or an uninsulated trailer.
2. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp
or other appliance;
b. Check to see if receptacle is connected to a light
switch which turns power off when you turn out
the lights;
c. If charging problems persist, take the tool, battery
pack and charger to your local service center.
3. You may charge a partially used pack whenever you
desire with no adverse effect on the battery pack.
Charger Cleaning Instructions
WARNING: Shock hazard. Disconnect the charger
from the AC outlet before cleaning. Dirt and grease
12
may be removed from the exterior of the charger using
a cloth or soft non‑metallic brush. Do not use water or
any cleaning solutions.
Wall Mounting
Some D
WALT chargers are designed to be wall mountable
e
or to sit upright on a table or work surface. If wall mounting,
locate the charger within reach of an electrical outlet, and
away from a corner or other obstructions which may impede
air flow. Use the back of the charger as a template for the
location of the mounting screws on the wall. Mount the
charger securely using drywall screws (purchased separately)
at least 1" (25.4 mm) long, with a screw head diameter of
0.28–0.35" (7–9 mm), screwed into wood to an optimal
depth leaving approximately 7/32" (5.5 mm) of the screw
exposed. Align the slots on the back of the charger with the
exposed screws and fully engage them in the slots.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
ASSEMBLY AND ADJUSTMENTS
DANGER: To reduce the risk of serious personal
injury, turn unit off and remove the safety key and
battery packs before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can cause injury.
Adjusting Handle Height (Fig. A, D)
The mower is shipped in storage mode. You will need to
adjust the handle to operating position before continuing.
1. To unlock the lower handle
position, twist the two handle lock knobs
turn. The handle lock knobs
of the lower handle
17
2. Raise the lower handle to the operating position. Take
care to not pinch or stress the cord.
3. Twist the handle lock knobs
the lower handle into position.
Attaching Upper Handle (Fig. A, E)
1. Line up the holes on the bottom of the upper handle
with the holes on the top of the lower handle
care to not pinch or stress the cord.
nOTE: Make sure the cord is located on the front of both
handles. If it is not it may result in the cord tangling and the
inability to easily store the mower.
2. From the inside of the lower handle
bolt
19
through the two handle holes. Repeat for the
opposite side.
3. From the outside of the upper handle tighten a handle
knob
18
onto each handle bolt
pinch or stress the cord.
Grass Collection Bag (Fig. F)
DANGER: Turn unit off and remove safety key and
battery packs.
1. Lift the rear door cover
bag
onto the mower so the bag lugs
13
into the slots
21
on the inside plastic surfaces of the
17
from the storage
7
a quarter
7
are located on both sides
.
7
a quarter turn, securing
17
4
, insert the handle
19
. Take care to not
and place the grass collection
12
slide
20
4
. Take
Tabla de contenido
