Black+Decker HRV425BL Manual De Instrucciones página 4

English
one robot vacuums are used at the same time, or if used in
a location exposed to a halogen lamp.
• Do not use the vacuum in the following environments:
ʵ Wet
ʵ Flammable
ʵ Explosive
ʵ Corrosive
ʵ Extreme hot
ʵ Extreme cold
• This vacuum is for indoor use only.
• Do not let this vacuum clean toner from a laser printer
or copier.
• Do not let this vacuum clean sharp objects, such as glass,
it may damage the vacuum.
• The charging station should be placed against a wall and
on a flat floor surface.
• Do not cover the signal window of the charging station.
• When storing this vacuum, charge the battery fully, turn
off the vacuum and place it in a cool dry place. Unplug the
charging station.
• Do not lift this vacuum by the front cover.
• Only for use with K25V240100X charger or with N501228
charging dock.
The vacuum is recommended for the
following floor surfaces:
• Hardwood/Laminate
• Ceramic/Stone tile
• Low and medium pile carpets
(plush carpeting is not recommended)
nOTE: Vacuum may not work on some black carpet and
darker floor surfaces, as the sensors may be detecting the
surface as a drop off.
Proper room preparation
• Place the cords from other appliances out of the area to
be cleaned.
• Do not operate the vacuum in a room where an infant or
child is sleeping.
• Do not operate the vacuum in an area where there are lit
candles or fragile objects on the floor to be cleaned.
• Do not operate the vacuum in a room that has lit candles
on furniture that the vacuum may accidentally hit or
bump into.
• Do not allow children to sit on the vacuum.
• Do not use the vacuum on a wet surface.
• Test the height of thresholds. Robot cannot climb
thresholds above 1/2 inch (10-15mm).
SAVE THESE
INSTRUCTIONS
Assembly
1. Remove front lens ( 8
2. Ensure the dust bin ( 9
fitted securely.
nOTE: The HRV425BLP contains a standard main brush and
an anti-tangle pet brush.
4
) protection film.
) and main brush ( 12 ) are
- For general daily maintenance cleaning, the
standard main brush should be used.
- Use the anti-tangle pet brush in areas where there is
pet or long human hair, areas with excessive hair on
floor surface, or areas that require a deeper clean.
Installing side brushes (Fig. B)
1. Ensure the power switch (
2. Place the vacuum upside down on a flat surface.
3. Locate the side brush retaining screws (
the packaging.
4. Place the side brushes (
5. Install side brush retaining screws.
Fig. B
20
21
Charging
(Fig. C)
Your vacuum can be manually charged via the jack plug or
automatically charged via the charging dock.
iMPORTAnT: The power switch (
position (I) for the vacuum to charge.
• Before first use, the battery must be charged for at least
4-5 hours.
nOTE: While charging, the charger may become warm. This
is normal and does not indicate a problem. The appliance
can be left connected to the charger indefinitely.

WARNING: Do not charge the battery at ambient
temperatures below 50 °F or above 104 °F.
Fig. C
1
Manually charge (Fig. D)
iMPORTAnT: The power switch (
position (I) for the vacuum to charge.
1. Plug the battery charger (
2. Slide the jack plug (
22
charging socket ( 2 ) of the vacuum.
3. The Start/Stop button (
short beep, meaning the vacuum is charging. The
Start/Stop button LED will turn off when the vacuum is
fully charged.
1 ) is in the off position (O).
20 ) from
) into the brush slots (
11 21
11
1 ) MUsT be in the ON
) MUsT be in the ON
1
) into a wall outlet.
18
) end of the charger into the
3 ) will blink and emit a single
) .
21