Technical Specifications; For Your Own Safety - RIDGID 540-2 Instrucciones De Uso

540-2
Operating Instructions
WARNING! Read these instructions and
the accompanying safety booklet care- fully before using this equipment. If you
are uncertain about any aspect of using this tool,
contact your RIDGID distributor for more infor-
mation.
Failure to understand and follow all instructions
may result in electric shock, fi re, and/or serious
personal injury.
SAVE THESE INSTRUCTIONS!

TECHNICAL SPECIFICATIONS

RIDGID 540
Input .................................................................................. 1500 W
Weight ................................................................................ 6.0 kg
No load speed r.p.m. ............................................................ 5300
Diamond cutting wheels Ø ......................................... 2 x 150 mm
Cutting depth max. ...................................................... 2 x 48 mm
Groove width ............................................................. 2.3 - 34 mm
Arbor Ø .............................................................................. 30 mm
Integrated vacuum cleaner adapter ................................. Included
Double insulated according to European safety standards.

FOR YOUR OWN SAFETY

• Read and save the enclosed safety instructions.
• Avoid damage that can be caused by screws, nails and other elements
in your workpiece.
• Always keep the cord away from moving parts of your tool.
• When you put away your tool, switch off the motor and ensure that all
moving parts have come to a complete standstill.
• In case of jamming, immediately switch off the tool and disconnect the
plug.
• Before using accessories always compare the maximum allowed
r.p.m. of that specifi c accessory with the r.p.m. of your tool.
• Never fasten an accessory key to your tool with a piece of rope or
something similar.
• Never use your tool without the original protection guard system.
• Avoid injury by using personal protection material like safety-goggles,
hearing protection, safety-gloves, safety-shoes, etc.
• Always use diamond cutting wheels with this tool.
• Do not use a diamond cutting wheel which is cracked or deformed.
• After switching off your wall chaser, never stop the rotation of the
diamond cutting wheel by a lateral force applied against it.
• Ensure that the cutting depth adjustment handle is always fi rmly fi xed
while you use the tool.
• Only use the fl anges and washers which are supplied with the tool.
• Do not cut material containing asbestos.
• This tool is not suitable for wet cutting.
GB
Ridge Tool Company
HOW TO HANDLE
• Mounting/removing of diamond cutting wheels (see fi g. 1).
- while loosening/tightening bolt A with wrench B spindlelock button
C should be pushed.
Change diamond cutting wheels with arrow printed on cutting
wheels pointing in same direction as arrow on protection
guard.
Always leave inner fl ange D on tool.
Make sure that clamping surfaces of fl anges and washers are
perfectly clean.
- check if diamond cutting wheels run freely by turning them by
hand.
• Adjusting cutting depth (see fi g. 2).
- for reaching maximum cutting depth in concrete, 3 subsequent
cuts are required: 15 mm, 30 mm and 48 mm.
Keep in mind that due to wear of the diamond cutting wheel,
cutting depth may differ.
- for easy adjustment of cutting depth you should align the material,
for which you intend to make the groove, with front and back
guiding rolls (not in between the diamond cutting wheels) and
adjust the cutting depth according to the material's diameter.
• Before using your tool a RIDGID vacuum cleaner should be connected
to integrated adapter E.
• Safety switch.
Prevents the tool from being switched on by accident.
- tool is switched on by fi rst pressing knob F with your thumb and
then pulling trigger G with your fi ngers.
- tool is switched off by releasing trigger G.
• Electronic soft start.
Ensures reaching the maximum speed smoothly without a sudden
impact when tool is switched on.
• Cutting vertical grooves (see fi g. 3).
- put front guiding rolls H at the top of the wall section to be cut.
- make sure that handle J points downwards.
- switch on your tool.
- wait until maximum speed has been reached.
- enter diamond cutting wheels gently into the wall until back guiding
rolls K also rest on the wall.
- gently move tool downwards.
• Electronic overload protection.
- protects motor from damage when tool is overloaded without
having to stop it and/or let it cool down for a period of time.
- as soon as reduction of motor speed is noticed you should reduce
pressure until speed is back to normal.
• Holding and guiding the tool (see fi g. 4).
- the tool can be guided in all directions.
Always follow cutting direction indicated by arrow on
protection guard.
Keep all 4 guiding rolls on the wall during cutting.
- hold the tool fi rmly, so you will have full control of the tool at all
times.
- do not apply too much pressure on the tool.
• Keep the air vent openings clean and uncovered.
• Adjusting groove width.
Sixteen different groove widths can be obtained by adjustment of the
washers as shown at the back of this instruction manual.
• Sighting edge for guiding tool along cutting line (see fi g. 5).
Always make trial cuts fi rst to verify actual cutting line.
• Before lifting your tool from the workpiece, you should switch off the
motor and ensure that all moving parts have come to a complete
standstill.
APPLICATION ADVICE
• Do not force the tool; let the speed on the diamond cutting wheel do
the work.
540-2
1