Important Safety Instructions; Tool Components And Specifications - Campbell Hausfeld CHG00189 Manual De Instrucciones De Operación

Operating Instructions

Important Safety Instructions

INSTRUCTIONS PERTaINING TO a
RISK OF FIRE, ElECTRIC SHOCK, OR
INJURY TO PERSONS
This manual contains safety, operational
and maintenance information. Contact
your Campbell Hausfeld representative
if you have any questions.
When using tools,
basic precautions
should always be followed, including
the following:
CalIFORNIa PROPOSITION 65
This product or
its power cord may
contain chemicals known to the State
of California to cause cancer and birth
defects or other reproductive harm.
Wash hands after handling.
You can create dust when
you cut, sand, drill or grind
materials such as wood,
paint, metal, concrete, cement, or other
masonry. This dust often contains
chemicals known to cause cancer, birth
defects, or other reproductive harm.
Wear protective gear.
GENERal
a. To reduce the risks of
electric shock, fire, and
injury to persons, read all
the instructions before
using the tool.

Tool Components and Specifications

• REqUIRES: 0.3 SCFM with
10 fasteners per minute @ 90 psi
• aIR INlET: 1/4 inch NPT
• FaSTENER SIZE RaNGE:
3/8 inch to 1-1/4 inch
• MaGaZINE CaPaCITY:
100 fasteners per load, 18 gauge
• STaPlES: 1/4 inch crown
• WEIGHT: 2 lbs., 15 oz.
• lENGTH: 10-1/2 inch
• HEIGHT: 9-1/2 inch
• MaXIMUM PRESSURE: 100 psi
• PRESSURE RaNGE: 60 psi to 100 psi
www.chpower.com
b. Be thoroughly familiar with the
controls and the proper use of the
equipment. Follow all instructions.
Contact your Campbell Hausfeld
representative if you have any
questions.
c. Only persons well acquainted with
these rules of safe operation should
be allowed to use the unit.
labels and manual. Failure to follow
warnings, dangers, and cautions could
result in DEATH or SERIOUS INJURY.
WORK aREa
a. Keep the work area clean and well
lighted. Cluttered benches and dark
areas increase the risks of electric
shock, fire, and injury to persons.
b. Do not operate the tool
in explosive atmospheres,
such as in the presence of
flammable liquids, gases,
or dust. The tool is able to create
sparks resulting in the ignition of
the dust or fumes.
c. Keep bystanders, children, and
visitors away while operating the
tool. Distractions are able to result in
the loss of control of the tool.
Quick
Clear
Nose
Work Contact Element (WCE)
PERSONal SaFETY
a. Stay alert. Watch what you are
Read and
understand tool
b. Dress properly. Do not wear loose
c. Avoid unintentional starting.
d. Do not overreach. Keep proper
e. Use safety equipment. A dust mask,
Cap Exhaust
Trigger
Fastener
Discharge Area
2
doing and use common sense
when operating the tool. Do not
use the tool while tired or under
the influence of drugs, alcohol,
or medication. A moment of
inattention while operating the
tool increases the risk of injury to
persons.
clothing or jewelry. Contain long
hair. Keep hair, clothing, and
gloves away from moving parts.
Loose clothes, jewelry, or long
hair increases the risk of injury to
persons as a result of being caught
in moving parts.
Be sure the switch is off before
connecting to the air supply. Do not
carry the tool with your finger on
the switch or connect the tool to the
air supply with the switch on.
footing and balance at all times.
Proper footing and balance enables
better control of the tool in
unexpected situations.
non-skid safety shoes and a hard
hat must be used for the applicable
conditions.
Latch Button
Magazine