Lutron SERENA CS-EDU3-SYJ Manual De Usuario página 3

Ocultar thumbs Ver también para SERENA CS-EDU3-SYJ:
Idiomas disponibles
  • ES

Idiomas disponibles

Serena
Manual Cellular Shade
TM
Installation Guide (please read before installing)
Step 1: Review Included Components
Before you begin, open the box and
Included:
make sure you have all the necessary
parts: the shade, mounting brackets,
and screws.
You will also need a cordless drill, a
Cellular shade
3/32 inch drill bit, a #2 Phillips bit, a
Tools required:
pencil, and a tape measure.
Drill
Step 2: Installing Mounting Brackets
Your shade was manufactured according to the mounting option you chose when
ordering your shade. Make sure you follow the appropriate mounting instructions:
inside mount,
outside mount on trim, or
Opt. A
Opt. B
Important:
Make sure you are screwing into wood studs.
If you're not mounting the brackets into wood studs, you'll need to use appropriate
fasteners for the mounting surface (not included).
Make sure the brackets are aligned with each other. (If not, the shade may not
properly snap into the brackets.)
Option A: Inside Mount
Hold the shade up to the window to make sure
A.1
it's the correct size.
Mark the center line for the two
A.2
outside brackets, 2 inches in from
each side of the window.
* NOTE: Shades wider than 45 inches
1
(vinyl headrail) or 48 inches (aluminum
headrail) will need a third bracket (
)
3
(included). Install this bracket in the
center of the shade.
Top view of shade wider than 45 inches
(continued)
or 48 inches
Lutron Electronics Co., Inc.
11/2013
7200 Suter Road
P/N 045356 Rev. E
Coopersburg, PA 18036-1299, U.S.A.
If the shade is wider than 72 inches,
English
you will need to install a third (
and a fourth bracket (
Install each of these one-third of the
way in from the outer brackets.
Center the bracket on the center line
A.3
and align it with the front edge of the
window trim. Mark hole locations and
then pre-drill holes for the screws.
Mounting
#6 Phillips
brackets
mounting
(Repeat for all brackets.)
screws
3/32 inch drill bit
Tape measure
#2 Phillips drill bit
Install the mounting brackets,
Pencil
#2 Phillips screwdriver
A.4
using the provided screws. Using
the cordless drill, drive each screw
through the holes in the top of
the bracket.
outside mount above trim.
Opt. C
Install the shade in the brackets.
A.5
Holding the shade in both hands,
tilt the top of the shade slightly away
from you and hook the front edge
into the brackets. Then gently
tilt the shade down and press the
bottom of the headrail until you hear
it click into place.
2 in
2 in
*
3
2
Important:
Be sure not to catch any fabric cells in the brackets.
3
4
1
/
/
1
1
)
3
3
3
) (included).
4
Top view of shade wider than 72 inches
Window frame
Bracket
Side view
Hook front edge
Press shade
Side view
e
e
Option B: Outside Mount On Trim
2
/
1
3
Hold the shade up to the window to make sure it's the
B.1
correct size. Center the shade and mark the trim at each
end of the shade.
Mark the center line for the two
B.2
outside brackets, 2 inches in from
the marks you made in step B.1.
* NOTE: Shades wider than 45 inches
(vinyl headrail) or 48 inches (aluminum
headrail) will need a third bracket (
3
(included). Install this bracket in the
center of the shade.
If the shade is wider than 72 inches,
you will need to install a third (
3
) and
a fourth bracket (
) (included). Install
4
each of these one-third of the way in
from the outer brackets.
Align the top of the brackets with the
B.3
top of the trim and the center line.
Mark the hole locations and then
pre-drill holes for the screws.
Install the mounting brackets using the
B.4
provided screws. Place each bracket
fl ush against the trim (using spacers*
Click
behind brackets if needed) and using
the cordless drill, drive each screw
through the holes in the bracket.
* NOTE: If window trim is angled, or not level vertically, place an angled spacer (not
included) behind each bracket. Ensure that the shade is level before placing the
bracket fl ush against the trim. Pre-drill a hole through the spacer as well.
Refer to step A.5 to install the shade in the brackets.
B.5
2 in
2 in
*
)
3
2
1
Top view of shade wider than 45 inches
or 48 inches
3
4
2
1
/
/
/
1
1
1
3
3
3
Top view of shade wider than 72 inches
Bracket Spacer*
Wall
Window
trim
Side view
loading

Este manual también es adecuado para:

Serena cs-edu3-syqSerena cs-edu3-sykSerena cs-edu3-sym