Fein Grit GIR Manual De Instrucciones página 8

en
8
Original Instructions.
Symbols, abbreviations and terms used.
The symbols in the Instruction Manual and on the
machine shall aide in directing your attention to possible
hazardous situations when working with this machine.
Symbol Term, meaning
Action
General mandatory sign
Read documentation
Danger warning
European conformity symbol
For your safety.
Do not use this machine before you have thor-
oughly read and completely understood these
operating instructions, including the figures, speci-
fications, and safety regulations.
Read and observe the Instruction Manuals of the
GI150/GI1502H belt grinder as well as the GIB/
GIBE undercarriage that are to be mounted to this
machine.
These operating instructions should be kept for later use
and enclosed with the power tool, should it be passed on
or sold.
Use only the fastening material provided for mounting the
radius grinding module to the belt grinder. When mounted
incorrectly, the radius grinding module can loosen itself
from the belt grinder during the working procedure and
lead to serious injuries.
Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety
glasses. As appropriate, wear dust mask, hearing
protectors, gloves and workshop apron capable of
stopping small abrasive or workpiece fragments.
The eye protection must be capable of stopping
flying debris generated by various operations. The
dust mask or respirator must be capable of filtrat-
ing particles generated by your operation. Pro-
longed exposure to high intensity noise may cause
hearing loss.
Make sure that all clamping levers and clamping fixtures
are firmly tightened. If the machine suddenly starts to
lower itself or if the work piece becomes loose during
the working procedure, serious injuries can result.
At a glance.
1 Cover/stop (GI 150/GI 150 2H)
2 Spark guard (GI 150/GI 150 2H)
3 Grinding rest (GI 150/GI 150 2H)
4 Dust collector (GI 150/GI 150 2H)
5 Side cover (GI 150/GI 150 2H)
6 Lever for swivel device (GIB/GIBE)
7 Belt tension lever (GI 150/GI 150 2H)
8 "Centre height" adjustment lever (pipe centre)
9 Clamping lever for "Centre height" adjustment
10 "Grinding depth/depth stop" adjustment
11 Crank for adjustment of work piece width
12 Collection receptacle
13 Work piece quick-clamping lever
14 Clamping jaws, fixed
15 Holding device/magazine for contact rollers
16 Star-knob bolt, height adjustment
17 Protective covers/side cover
18 Contact roller
19 Locking screw for contact roller
20 Clamping lever for angle adjustment
21 Fixing bushing
22 Bolts for fixing bushings
23 Holes quicklock
24 Quicklock
25 Lever for quicklock
26 Nuts for belt-traction
27 Screws for belt-traction
28 Table adjusting Crank
29 Feed Lever
Intended use of the machine.
The radius grinding modules GIR are to be used together
with the GI150/GI1502H belt grinder and exclusively for
grinding off pipe ends.
Roller with a diameter smaller than 35 mm may not
be processed with the GI 150 belt grinder!
Mounting instructions (Figure 1/2).
Belt grinder GI 150 2H.
Before any work on the machine itself, pull the power
plug from the socket outlet.
Dismount the top cover (1) together with the spark
guard (2).
Dismount the grinding rest (3) and the dust collec-
tor (4).
Open the side cover (5).
Loosen the belt tension lever (7) and remove the
grinding belt.
Close the side cover.
Undercarriage GIB/GIBE.
Loosen the lever for the swivel device (6) and posi-
tion the GI150/GI1502H approx. level.
GIR.
Take the module out of the packaging and mount the
accessories as described in the data sheet.
Loosen the four mounting bolts (20) of the upper
part at the front and rear of the foot pedestal.
Mount the 4 fixing bushings (21) with the 4 bolts
(22).
Align the 4 holes (23) with the 4 fixing bushings (21).
Slide the GIR against the GI150/GI1502H belt
grinder.
Slide the 2 quicklocks (24) to the left and tighten the
2 levers (25). Loosen the swivel device of the under-
carriage again if the holes are not aligned.