Atlas Copco Dynapac SD1800C Manejo Y Mantenimiento página 224

KWP SPN FMI
1169 523951 1
1170 523612 12
1171 175 2
1173 523973 14
1174 523974 14
1175 523975 14
1176 523976 14
1177 523977 14
1178 523978 14
1180 168 0
1181 168 1
1182 172 0
1183 172 1
1187 523980 14
1192 523922 12
1193 1180 0
1194 1180 1
1216 523914 5
1217 523914 11
1219 524018 14
1220 524022 14
1221 524023 14
1222 190 14
D 23.18 68
Code Error Identification
7-7-2 Zerofuel calibration injector 6 (in firing
order); minimum value exceeded
5-5-5 ECU reported internal software error
1-4-4 Oil temperature; plausibility error
7-7-9 SCR Tamper detection; derating timer
below limit 1
7-7-9 SCR Tamper detection; derating timer
below limit 2
7-8-0 Urea quality; derating timer below limit 1
7-8-0 Urea qulaity; derating timer below limit 2
7-8-1 Urea tank level; derating timer below limit
1
7-8-1 Urea tank level; derating timer below limit
2
3-1-8 Physikal range check high for battery
voltage
3-1-8 Physikal range check low for battery volt-
age
2-2-6 Physical range check high for intake air
temperature
2-2-6 Physical range check low for intake air
temperature
7-8-4 Bad quality of reduction agent detected
Over temperature error on burner shut of
valve
Exhaust gas temperature upstream tur-
bine; out of range, system reaction initi-
ated
Exhaust gas temperature upstream tur-
bine; out of range, system reaction initi-
ated
8-5-1 Glow plug control; open load
8-5-1 Glow plug control; internal error
7-8-6 DPF wasn´t regenerated, power reduc-
tion phase 1 (manuell regeneration
request)
7-8-6 DPF wasn´t regenerated, power reduc-
tion phase 2 (manuell regeneration
request)
7-8-6 DPF wasn´t regenerated, warning condi-
tion (manuell regeneration mode)
2-1-2 Speed detection; out of range, signal dis-
rupted
Short Text Detail
Zerofuel calibration injector 6 (in firing order);
minimum value exceeded
Internal software error ECU
Customer oiltemperature: signal unplausible
SCR Tamper detection; derating timer below
limit 1
SCR Tamper detection; derating timer below
limit 2
Urea quality; derating timer below limit 1
Urea qulaity; derating timer below limit 2
Urea tank level; derating timer below limit 1
Urea tank level; derating timer below limit 2
Physikal range check high for battery voltage
Physikal range check low for battery voltage
Physical range check high for intake air tem-
perature
Physical range check low for intake air temper-
ature
Bad quality of reduction agent detected
Over temperature error on burner shut of valve
Physical range check high for exhaust gas tem-
perature upstream turbine
Physical range check low for exhaust gas tem-
perature upstream turbine
Glow plug control release line; short circuit
error
Glow plug control; internal error
DPF wasn´t regenerated, power reduction
phase 1 (manuell regeneration request)
DPF wasn´t regenerated, power reduction
phase 2 (manuell regeneration request)
DPF wasn´t regenerated, warning condition
(manuell regeneration mode)
Camshaft- and Crankshaft speed sensor signal
not available on CAN