Hilti POS 150 Manual De Instrucciones Original página 23

▶ Adopt the correct posture when working. Maintain proper footing and balance at all times. This
will allow you to control the scanning tool better, even in unexpected situations.
▶ Wear your personal protective equipment and always wear protective glasses. Depending on the
type of scanning tool you are using and its purpose, wearing safety equipment such as a dust mask,
slip-resistant safety shoes, a hard hat or hearing protection will reduce the risk of injury.
▶ Avoid starting the tool accidentally. Make sure that the scanning tool is switched off before
connecting it to the battery and before picking it up or carrying it. Carrying scanning tools with your
finger on the switch or plugging in scanning tools that are already switched on can cause accidents.
Using and handling the scanning tool
▶ Do not use a scanning tool if it has a faulty on/off switch. A scanning tool that can no longer be
switched on or off is dangerous and must be repaired.
▶ Store scanning tools out of reach of children when not in use. Do not allow persons who are not familiar
with the product or these instructions to operate it. Scanning tools are dangerous in the hands of
inexperienced persons.
▶ Scanning tools need care and attention. Check that moving parts operate satisfactorily and do not
jam, and make sure that no parts are broken or damaged in such a way that the scanning tool might no
longer function correctly. Have damaged parts repaired before using the scanning tool. Many accidents
are caused by poorly maintained scanning tools.
Using and handling the cordless power tool
▶ Use only the specified batteries in the scanning tools. Use of other batteries can result in injury and a
risk of fire.
▶ Recharge the batteries only with the chargers recommended by the manufacturer. A charger that is
suitable for a certain type of battery can be a fire hazard if used with other batteries.
▶ When the battery is not in use, keep it away from other metal objects such as paper clips, coins,
keys, nails, screws, or other small metal objects that could cause bridging between the terminals.
A short circuit between the battery terminals may cause burns or a fire.
▶ Liquid may leak from the battery if used incorrectly. Avoid contact with this liquid. Liquid leaking
from the battery may cause skin irritation or burns. If contact accidentally occurs, rinse with water. Seek
medical attention if the liquid comes into contact with the eyes.
2.2 Battery use and care
▶ Observe the special regulations and instructions applicable to the transport, storage and use of Li-ion
batteries.
▶ Do not expose batteries to high temperatures, direct sunlight or fire.
▶ Do not disassemble, crush or incinerate batteries and do not subject them to temperatures over 80 °C.
▶ Do not use or charge batteries that have suffered mechanical impact, have been dropped from a height
or show signs of damage. In this case, always contact your Hilti Service.
▶ If the battery is too hot to touch it may be defective. In this case, place the product in a non-flammable
location, well away from flammable materials, where it can be kept under observation and allowed to
cool down. In this case, always contact your Hilti Service.
2.3 Safety instructions, total station
▶ Do not render safety devices ineffective and do not remove information and warning notices.
▶ If the product is opened improperly, laser radiation in excess of Class 2 may be emitted. Have the
product repaired by Hilti Service only.
▶ Check that the product functions correctly each time before use.
▶ Measurements taken through panes of glass or other objects may be inaccurate.
▶ The measurement may be incorrect if the conditions under which the measurement is taken change
rapidly, e.g. due to people walking through the path of the laser beam.
▶ Observe the information printed in the operating instructions concerning operation, care and maintenance.
▶ Do not use the product as a level.
▶ Do not point the product toward the sun or other powerful light sources.
▶ Although the product is designed for the tough conditions of construction site use, as with other
measuring instruments it should be treated with care.
▶ Check the accuracy of the product after it has been dropped or subjected to other mechanical stresses.
▶ Secure the site at which you are taking measurements and take care to avoid directing the laser beam
toward other persons or toward yourself.
2035736
*2035736*
Printed: 08.05.2018 | Doc-Nr: PUB / 5153826 / 000 / 04
English 17