Pahlen 300A Classic Manual De Instrucciones página 5

LED light type 300 Classic
Type 300A, concrete:
Item no 123281
Item no 123381
The pool light shall be connected through an isolation transformer 12V 60W/300W, see circuit diagram on the opposite page.
Pay attention to local electric directions as to the placing of the junction box.
Install the niche in the pool wall. Apply some waterproof grease in the threads of the niche.
Thread the cable conduit in the niche and in the junction box. The thread shall be sealed
with e.g. thread tape. The cable conduit shall be placed so that the bend radius is not
below 100 mm.
For the 300A: The front edge of the niche shall be in line with the concrete wall
(see sketch below).
For the 300CA: After fitting the liner, fill water up to about 10 cm below the niche.
Fit the plastic front ring and the gaskets to make the liner tight
against the niche, (see exploded view below).
Insert the cable in the conduit and connect to the junction box.
Tighten the fitting in the junction box to seal the cable.
Place the socket on the cable of the lamp where it runs
through the cable gland of the niche. Tighten that cable gland.
Wrap excess cable behind the lamp and assemble the
lighting unit in the niche.
The light must be completely covered with water
before lighting.
Recommended values for water quality:
Total chlorine content: max 3.5 mg/liter (ppm)*
Chloride (salt) content: max 250 mg/liter
pH-value: 7.2–7.6
Alkalinity: 60–120 mg/liter (ppm)
Calcium hardness: 100–300 mg/liter (ppm)
Iron: max 0.1 mg/l *
Copper: max 0.2 mg/l *
Manganese: max 0.05 mg/l *
Phosphorus: max 0.01 mg/l *
Nitrate: max 50 mg/l *
Outside these values the product warranty does not apply.
Type 300A
Wall type: 200 mm tiled concrete
· .. · .
.
- .
· . · ..
. · • .
......
. Ll
. '• . . .. - · .
<J ......
<JL'.i/: / :
;
-· · :
,1
·::::: .
. .
-
· · · ·
· ::::::
.
· <J
�- . . -.
. . .
:
. .. .
.
· : · • : ·
· .
. · . •·
· . ·
' • .
. . . <J
· .. . . '\: / :
. · . · . ,,, .
• , · · · <J
.
: ::::::
. . .. ,1
--
-- ., . ,1
· .
· .. ::::::
. :
Ll
;:�: <J
. .
::::::
� . - · .
_
, --<
_
______ ::::::
· - · - .
.
�
---
_______ .
......_
: .
<J
·
.6
<l·
.
Ll
'°
..--i
"&
,1
<J
--
_ _ _ __ 4_
10
35
200
LED light red/green/blue
LED light white
Complies to EN 16713-3
Exploded view pool light 300CA
1. Nut M6 + Washer (3 pcs)
2. Framework
3. Conduit
4. Gasket self-adhesive
Type 300CA
Wall type: plywood on frame work or
galvanized steel
Pahlén AB
·--,
___
�
_ .
.
__
-----...._·
__
� .
---·--._ - . .
'--.
0
0
'&
c..o
OC)
tj-
OC)
0
N
n
'&
---·-- · -·
�
.
25-30
Type 300CA, liner:
Item no 123291
Item no 123391
BELEUCHTUNG
Art. nr. 12270
E
Box 728, SE-194 27 Upplands Väsby, Sweden
Phone +46 8 59411050, Fax +46 8 59086880
5. Gasket
6. Countersunk screw M6x20 (8 pcs)
7. Screw M5x20 (2 pcs)
8. Lighting unit
Type 300CA
Wall type: building blocks with insulation and liner
Box 728, S-194 27 Upplands Väsby, Sweden, Phone +46 8 594 110 50, Fax +46 8 590 868 80
---
CX)
CX)
N
B-
�
.
�
140
5
ENGLISH
LED light red/green/blue
LED light white
UP
45°
BELYSNING
LIGHTING
TYP 300 CA
n 240
n 12(3x)
Ø257
Surface treatment Designed by:
The tolerance class in accordance with this Assembly drawing no.
part of ISO 2768
Håltagningsmall för
belysning typ 300 CA vinyl
9. Plastic front ring
10. Liner
11. Niche
12. Junction box
--
�
�
·
<1
Ll
_. Ll
<1
.Ll
A
Ll
<I·
0
Ll.
CD
Ll
..--
.
<1
0
"0-
..--
<1
"0-
Ll
<I
Ll
<1
Ll
----
i------1 40
------<-1
n
14(8x)
Drawn by: Date Approved by:
OA 2006-04-26
Art.no.
Scale Revised by: Date
1:2 OA 2007-09-20
Drawing number Rev.no.
M10112 2
File: R10198-3.cdr
CX)
CX)
"0-