Expert" Default Parameters; Start-Up; Verifying The Diagnostic Leds; Setup - FAAC B680H Manual De Instrucciones
Ocultar thumbs
Ver también para B680H:
- Guia de inicio rapido (2 páginas) ,
- Traducción del manual original (44 páginas)
Tabla de contenido
Idiomas disponibles
Idiomas disponibles
6.4 "Expert" default parameters
The following table contains the pre-defined settings that characterize
the various operation logics.
Step.
A
A1
E
0 1
Y
Y
N
02
N
N
N
03
N
N
N
04
N
N
N
05
N
N
Y
06
N
N
Y
07
N
N
N
08
N
N
N
09
N
N
N
10
N
N
N
1 1
N
N
N
12
N
N
N
13
N
N
N
14
N
N
N
15
N
N
N
16
N
N
N
17
N
Y
N
18
N
Y
N
19
N
N
N
20
N
Y
N
2 1
N
Y
N
22
N
N
N
23
N
N
N
24
N
N
N
25
N
N
N
26
N
N
N
27
N
N
N
28
N
N
N
29
N
N
N
30
N
N
N
7. START-UP
7.1 Verifying the diagnostic LEDs
Before starting up the board, it is necessary to verify that the status
of the diagnostic LEDs corresponds to the logic. Said status must
coincide with the indications in Fig. 4, situation which reflects that of
an automated system that is CLOSED and ready to open.
The FSW, STOP and ALARM LEDs are safety inputs with
NC contacts, therefore the related LEDs must be ON
when the automated system is at rest, and go off when
the device connected is engaged.
The OPEN and CLOSE inputs are NO contact inputs,
therefore the related LEDs must be OFF when the
automated system is at rest, and go on when the device
connected is active.
The BUS status must correspond to DL2 (green) on fixed
and DL1 (red) off. The BUS menu of the
Basic configuration must display the
indication shown to the side confirming
the fact that there are no engaged
photocells or active pulse generators.
P
PA
Cn
Ca
C
N
Y
N
Y
N
Y
Y
Y
Y
Y
N
N
N
N
N
N
N
N
N
Y
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Y
N
N
N
N
N
Y
Y
N
N
N
N
N
N
N
N
Y
Y
Y
Y
N
N
N
N
N
N
Y
Y
N
N
N
N
N
N
N
N
N
N
N
N
N
Y
Y
N
N
N
Y
Y
Y
Y
N
Y
Y
Y
Y
N
N
N
N
N
N
Y
Y
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Y
Y
N
Fig. 4
M1
DL15
J11
J14
ENCODER
J7
DL1 DL2
J6
J1
1 2
3 4 5 6 7 8 9 10 11
7.2 Setup
Before being put into operation, the E680 board requires a setup
procedure during which the automated system determines the rotation
angle of the beam and consequently its travel. These measurements
allow correct management of motor decelerations and acceleration
ramps.
At first start-up the board will signal the need for a setup
cycle, by displaying a flashing
For setup, proceed as follows:
•
Using the parameter "Mt" in Basic configuration mode, check that
the opening / closing movement corresponds to the pressed key
(+ / -); if not, go to the motor wiring and reverse the two conductors
L1 and L3, as shown in Fig. 14, Ref. d
•
Place the automated system in closing position using the
parameter "Mt" in Basic configuration mode or using the release
device, as shown in paragraphs 6 and 7 on page 4.
•
Press and hold SW4 ("SETUP" programming key) until the
automated system begins a slow opening movement. On the
S1
display
will flash indicating the start of the procedure.
•
Once the maximum opening position is reached, the automated
system will stop automatically.
•
Next, the automated system will start the beam closing
movement. The display will flash the indication
•
Once the closing position has been reached, the automated
system will stop automatically and the display will go back to
showing the indication of the current status of the automated
00
system (
- closed).
8. TESTING THE AUTOMATED SYSTEM
Once programming is completed, ensure that the system is operating
correctly.
Verify especially the correct regulation of the automated system power
and correct operation of the safety devices it is connected to and verify
that the automated system conforms to current safety standards.
18
BATTERY
DISP1
+
-
F
Sw1 Sw2 Sw3
J15
J2
J3
12 13 14 15 16 17 18 19 20 21
22 23
18 19 20 21
S0
.
S3
.
J13
J12
J4
Capítulos
Tabla de contenido
