JB Systems Light LOUNGE LASER DMX Manual De Instrucciones página 6

ENGLISH
Some more information on DMX512:
The DMX-protocol is a widely used high speed signal to control intelligent light
equipment. You need to "daisy chain" your DMX controller and all the connected light
effects with a good quality XLR M/F balanced cable. To prevent strange behavior of
the light effects, due to interferences, you must use a 90Ω to 120Ω terminator at the
end of the chain. Never use Y-splitter cables, this simply won't work!
Each effect in the chain needs to have its proper starting address so it knows which commands from the
controller it has to decode.
1 CHANNEL DMX-CONFIGURATION OF THE LASER:
CHANNEL VALUE DESCRIPTION
000-007 Laser off (black out)
1 008-100 ArA, Automatic random play
101-170 SrA, Slow random play
171-255 Sou, Sound activated random play
7 CHANNEL DMX-CONFIGURATION OF THE LASER:
CHANNEL VALUE DESCRIPTION
1 000-051 Laser output in blackout
MODE 052-102 ArA, Automatic random play
SELECT 103-154 SrA, Slow random play
155-206 Sou, Sound activated random play
207-255 Laser in DMX mode
2 000-004 Blackout
RED 005-127 Laser on
LASER 128-254 Strobe frequency from fast to slow
STROBE 255-255 Sound controlled strobe
3 000-004 Blackout
GREEN 005-127 Laser on
LASER 128-254 Strobe frequency from fast to slow
STROBE 255-255 Sound controlled strobe
4 000-004 No rotation
ROTATION 005-127 Clockwise rotation from slow to fast
LASER 128-133 No rotation
DOTS 134-255 Counterclockwise rotation from slow to fast
5 000-004 No rotation
ROTATION 005-127 Clockwise rotation from slow to fast
LED 128-133 No rotation
EFFECT 134-255 Counterclockwise rotation from slow to fast
6 000-004 Blackout
DIMMER LED 005-255 Dimmer level from low to high
7 000-004 Blackout
LED 005-127 LED on
STROBE 128-254 Strobe frequency from fast to slow
255-255 Sound controlled strobe
MAINTENANCE
 Make sure the area below the installation place is free from unwanted persons during servicing.
 Switch off the unit, unplug the mains cable and wait until the unit has been cooled down.
During inspection the following points should be checked:
 All screws used for installing the device and any of its parts should be tightly fastened and may not be
corroded.
 Housings, fixations and installations spots (ceiling, truss, suspensions) should be totally free from any
deformation.
 When an optical lens is visibly damaged due to cracks or deep scratches, it must be replaced.
JB SYSTEMS
®
OPERATION MANUAL
7/48 LOUNGE LASER DMX
ENGLISH
 The mains cables must be in impeccable condition and should be replaced immediately when even a
small problem is detected.
 In order to protect the device from overheat the cooling fans (if any) and ventilation openings should be
cleaned monthly.
 The interior of the device should be cleaned annually using a vacuum cleaner or air-jet.
 The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp,
smoky or particularly dirty surroundings can cause greater accumulation of dirt on the unit's optics.
 Clean with a soft cloth using normal glass cleaning products.
 Always dry the parts carefully.
 Clean the external optics at least once every 30 days.
 Clean the internal optics at least every 90 days.
Attention: We strongly recommend internal cleaning to be carried out by qualified personnel!
SPECIFICATIONS
Mains Input: AC 100~240V, 50/60Hz
Fuse: 250V 1A slow blow (20mm glass)
Power consumption:
15 Watt
Laser Power: 40mW Green CW laser (λ = 532nm)
150mW Red CW laser (λ = 650nm)
Laser radiation class: 3B
Laser Safety Standard: EN/IEC 60825-1 Ed2, 2007-03
Safe ambient temperature: 10°C – 40°C
LED Power 5W (blue – 455nm)
DMX in/out: 3pin XLR male/female
Weight: 1,6kg
Every information is subject to change without prior notice
You can download the latest version of this user manual on our website: www.beglec.com
JB SYSTEMS
®
OPERATION MANUAL
8/48 LOUNGE LASER DMX