Power Supply - Ferm TSM1035 Manual Original

conductors of at least 1,5 mm
with a 16 A fuse. Be sure that this extension
cable is not longer than 20 metres.
• This machine can be switched to the single-
phase network (230-240 V/50 Hz). If you are
in doubt about the earth of the electricity
provisions, consult an electrician first.

Power supply

• The motor is fitted with an overload switch.
If the table saw overloads, the overload switch
switches the equipment off automatically to
protect the table saw from overheating. If the
overload switch triggers, switch off the table
saw using the ON/OFF switch (8) and wait
until the table saw cools down. Then press the
ON/OFF switch (8) and restart the table saw.
3. ASSEMBLY INSTRUCTIONS
Assembly of the undercarriage
Fig A4
First assemble all parts before firmly
tightening all bolts.
• Put the machine upside down. Put a piece
of cardboard underneath, so you don't
damage the subsurface.
• Mount the legs (15) (4 pcs) with one
extension support (13) (4 pcs) per leg on the
four corners of the body, use longer bolts (16)
with nuts (2 pcs per leg) (Fig.B1)
• Make sure the extension supports (13) are
mounted in the same way as shown in Fig.B1
• Mount Cross strut long (22A) (2 pcs) between
the legs on the front and back side of the
machine. Use small bolts (25) with nuts (8 pcs).
• Mount Cross strut short (22B) (2 pcs) between
the legs on both sides of the machine. Use
small bolts (25) with nuts (8 pcs).
• Place the rubber feet (23) (4 pcs)
• Mount the additional legs (24) (2 pcs) on the
backside of the machine, use small bolts (26)
with nuts (4 pcs)
Assembly of the extensions
Fig B1, Machine is still upside down
• Mount the extensions (3) (2 pcs) to the table,
use small bolts (17) with nuts (4 pcs).
and protected • Mount the extensions support (13) to the ex-
2
ten sions (3), use small bolts (17) with nuts (4 pcs)
• Turn the machine back on its feet. Make sure
the extensions are levelled with the table, by
using the slots in the extensions supports.
Assembly of the riving knife
Fig A4, C
• Remove the inlay (21) from the table, by using
a screwdriver (Fig.G1).
• Loosen the fixing screw (28)(Fig.C1)
• Raise the riving knife until the depth between
the saw table and the upper edge of the riving
knife equals approx. 110mm (Fig.C2)
• The distance between the riving knife and the
toothed rim of the saw blade must be between
3 and 5 mm (Fig.C3).
• The tip of the riving knife shall not be lower
than 5 mm from the tooth peak, as shown in
Fig.C3.
Attachment of the guard
Fig C4
• Turn sawblade completely upwards
(instructions for height adjustment see chapter 4)
• Pull the knob (19) of the guard (5) and place it
over the riving knife (20) while pulling the knob
• Release the knob and make sure the pin slides
in the hole
• Secure the guard by tightening the knob
Assembly of the dust extraction
Fig. D
• Assemble dust extraction like shown on Fig.D
• Attach the vacuum cleaner to the vacuum
cleaner connection (27)(Fig.D)
Attachment of the parallel guide
Fig E
• Attach the parallel guide (2A) on the right side
off the saw blade on the table.
• Lock the guide down by pushing down the
handle (Fig.E)
Attachment of the parralel guide holder
Fig. I
The parallel guide can be stored using the holder
clips (30). Mount the holder clips (30) using
carriage-type bolts with nuts (29). The holders
can be mounted as shown in Fig I1 or as shown
in Fig I2.
11