Evc 2.0, Evc-E And Evc-D - Volvo Penta NMEA2000 Instrucciones De Montaje


Purpose
Install Easy Connect, on boat/engine's electronic network.
Bluetooth code
Note: you will need the six-digit bluetooth code printed on
the interface label for connection to your device (phone,
tablet, etc.). See C in Fig. 8. Record the code number before
mounting the interface.
Record code here: _________________________
Parts included;
P/N Name
interface
23197513 harness
23305065 harness
948210 cable ties
Installation
WARNING! to prevent accidental starting,
disconnect engine power at the battery switch,
tag battery switch and all ignition switches to
alert others that work is being done on the
engine.
NOTICE! The interface and adapter harnesses must
be mounted securely, away from moving parts, excess
heat, and wet areas. Use the cable ties to secure the
interface. All harness and cable installations must meet
ABYC, USCG, EU and other applicable regulations and
standards.
Mount the interface where the LED lights can be seen, for
system diagnostics.

EVC 2.0, EVC-E and EVC-D

Connect interface to the multilink hub according to figure 1;
option A - directly to hub, or
option B - use Y-cable to install in-line
Gas engines without EVC
See figure 2.
Extension harnesses must be ordered if the interface is
mounted away from the engine.
For twin installations, use an interface on each engine.
A - Easy Connect connector on engine (2019 to present)
No adapter cable needed.
Connector is on the rear of the engine.
B - 6-pin VODIA connector (2010 to 2019)
Use adapter harness 23305065 to connect the interface to
the engine harness VODIA connector. The connector is
located near the fuse box.
6
23870792 23870793 23870794
1 1
1
2 2
C - 8-pin VODIA connector (2006-2009)
An additional harness is needed to complete the installation.
Order one 3883170 adapter harness for each engine. Install
the interface and adapter harnesses according to figure 2.
B and C
The Vodia connector is still powered at key off; the LEDs are
still active and will draw a very small amount of current.
During storage this could drain the batteries. Disconnect
engine electrical power to prevent.
Earlier EVC
Version
C
B
A
MDI
EVC-A
1
Y-harness 23789703 is required to connect the interface to
the EVC network.
The third leg of the Y-harness must be terminated.
1
On twin installations this leg is connected to X5 on the
second HCU, which provides the termination.
2
On single installations terminal plug 881829 must be
installed on the open leg.
D1/D2 MDI
Use cable 23900247 to connect to the multilink and NMEA
2000 backbone. This connection powers the interface when
the engine is not running. See figure 7.
NMEA2000
The interface will also broadcast data from the boat's
NMEA2000 network. Connect the interface's NMEA2000
connector to the NMEA2000 backbone to access this data.
System Status LEDs
See figure 8.
G - Green LED - diagnostics;
Flashes On-Off-On-Off-On, the device has power supply and
communication on both NMEA and EVC/Engine.
On constantly, the unit has power supply but no
communication, either on NMEA or EVC/Engine.
Flashing twice and then off (500ms), repeatedly, then the unit
has power supply and communication on EVC/Engine but
not on NMEA.
Flashing three times and then off (500ms), repeatedly, then
the unit has power supply and communication on NMEA but
not on EVC/Engine.
B - Blue LED - bluetooth status;
Flashes On-Off-On-Off-On, unit is paired and working.
Not lit, bluetooth device in interface is not working.
On constantly, bluetooth interface is working but not paired.
Flashing twice and then off (500ms), repeatedly, error in
bluetooth communication.
Schematic
fig. 3
fig. 4
fig. 5
fig. 6
47712640 06-2020 © AB Volvo Penta