Attaching The Additional Handle; Power Supply; Attaching The Grinding Wheel - Metabo W 14-125 Ergo Instrucciones De Manejo

Use a suitable extraction unit.
Reduce dust exposure with the following measures:
- Do not direct the escaping particles and the
exhaust air stream at yourself or nearby persons
or on dust deposits.
- Use an extraction unit and/or air purifiers
- Ensure good ventilation of the workplace and
keep clean using a vacuum cleaner Sweeping or
blowing stirs up dust
- Vacuum or wash protective clothing Do not blow,
beat or brush.
Symbols on the tool:
.......... Class II Construction
V ............. volts
A ............. amperes
Hz ........... hertz
W ............ watts
Ø............. max. diameter of the accessory
.../min...... revolutions per minute
rpm ......... revolutions per minute
~ ............. alternating current
............ alternating current /direct current
n.............. rated speed
The "C" and "US" indicators adjacent to the
CSA Mark signify that the product has been
evaluated to the applicable CSA and ANSI/
UL Standards, for use in Canada and the U.S.,
respectively.
4. Overview
See page 2.
1 Support flange
2 Spindle
3 Spindle locking button
4 Lock (to prevent the machine from being switched
on unintentionally, or for continuous operation)*
5 Trigger ( for switching on and off)
6 Button (to turn the main handle)*
7 Main handle
8 Additional handle / Additional handle with vibration
damping *
9 Safety guard
10 Clamping nut *
11 2-hole spanner *
12 Lever (to adjust safety guard without the use of
tools)
* depending on equipment/not in scope of delivery
5. Commissioning
Before plugging in, check to see that the rated
mains voltage and mains frequency, as
specified on the rating label, match your power
supply.
Always install an RCD (GFCI) with a max. trip
current of 30 mA upstream.
5.1

Attaching the additional handle

Always work with the additional handle
attached (8)! Manually screw in the additional
handle securely in the left, centre or right threaded
hole (depending on requirements).
5.2 Attaching the safety guard
(for work involving grinding wheels)
For reasons of safety, the safety guard (9)
should always be attached when roughing
work is performed.
For reasons of safety, the special parting
guard should always be attached before
parting work is performed (see chapter 10.
Accessories).
See illustration E on page 2.
- Push and hold the lever (12). Place the safety
guard (9) in the position indicated.
- Release the lever and turn the safety guard until
the lever engages.
- Push the lever and turn the safety guard until the
closed section is facing the operator.
- Make sure that the guard is seated securely: the
lever must engage and you should not be able to
turn the safety guard.
5.3 Rotatable main handle
Only work with the main handle (7) engaged.
See illustration B on page 2.
- Push in the button (6).
- The main handle (7) can now be turned 90° to both
sides and can be engaged.
- Make sure that it is securely positioned: the main
handle (7) must be engaged and it should not be
possible to move it.
5.4

Power supply

The mains sockets must be protected using time-
delay fuses or circuit breakers.

6. Attaching the grinding wheel

Disconnect the mains plug before changing
any accessories. The machine must be
switched off and the spindle at a standstill.
For reasons of safety, attach the parting guard
before performing parting work (see chapter
10. Accessories).
6.1 Locking the spindle
Press in the spindle locking button (3) only
when the spindle is stationary!
- Press in the spindle locking button (3) and turn the
spindle
(2) by hand until you feel the spindle locking
button engage.
6.2 Placing the grinding wheel in position
See illustration C on page 2.
ENGLISH en
Use only accessories that
are covered by at least 3.4
mm by the safety guard.
9