Use Instructions - BERTO'S PLUS 600 Serie Manual De Instrucciones

In models E9BM4M, E9BM8M, SE9BM4M, SE9BM8M the
terminal board is situated in the line-arrival box inside
the appliance compartment. Open the doors (B), if
present, to reach the box.
3) Connect the circuit breaker switch (A) to the terminal
board (H) as shown in the figure and the wiring
diagrams at the beginning of the manual. The chosen
connection cable must have features similar to the
H07RN-F type with an operating temperature of at least
80 °C and have a section suitable to the unit (see the
Technical Data table).
4) Pass the cable through the passage and tighten
the cable stopper, connect the conductors in their corresponding position to the terminal board and
attach them. The yellow-green ground conductor must
be longer than the others so that, in the event that
the cable stopper breaks, it disconnects itself after the
voltage cables.
Equipotential
The appliance has to be connected to an equipotential
system. The connection terminal is on the bottom or the
back of the appliance and marked with the following
symbol:
Connection to the water network
The appliance must be connected permanently to the
water network; never use a flexible pipe connection set.
If possible, connect the water inlet pipe to the water
MOD. N°:
network by a mechanical filter and a shut-off tap. Before
V kW: Hz: 50/60 IPX4
connecting the filter, allow the water to flow for a short
time to eliminate any possible ferrous residuals from the
duct.
Water discharge
Connect the overflow discharge pipe to the sewage
network.
Attention!
The manufacturer is not responsible and will not
reimburse, under the guarantee, damages due to the
improper installation and installation that does not
conform to these instructions.
APPLIANCE TEST
Important
Before putting it in operation, test the equipment
to evaluate the operational conditions of each
component and single out any possible anomalies.
During this phase, it is important that safety and
hygiene conditions are strictly followed.
Carry out the following controls to perform the test:
1) Check that the main voltage is in conformity with the
appliance voltage
2) Use the automatic disconnecting switch to check the
electrical connection
3) Check the proper operation of safety devices
After testing, if necessary, train the users so that they
understand all necessary skills to operate the equipment
in safe conditions, according to the regulations in force in
the country in which the equipment is to be used.

USE INSTRUCTIONS

ATTENTION!
This appliance cannot be used by people (including
children) with impaired skills or without experience
and knowledge unless under the supervision of a
person responsible for their safety who provides
precise instructions about the use of the unit.
Keep children under supervision to make sure that
they don't play with the unit.
Use the appliances under supervision and never
operate while empty. The maximum resistance
pressure of the pasta cookers and bain-marie is 700
kpascal.
Pilot lights indicate if every unit is on or off.
The appliance does not need particular adjustment
interventions by specialized people except for the
regulations made during the user's operation.
Use only the accessories recommended by the
manufacturer. During the initial uses of the appliance,
an acrid or burning smell may be detected. This will
disappear after two or three uses.
After use, the areas are hot for a certain amount of time
(residual heat). Avoid resting your hands on them and
allowing children to get too close!
These are very important regulations; if they are
neglected, the appliance may not perform properly or
the user may be placed at risk.
OPERATION
Before using the unit for the first time, clean the tank
properly (see the paragraph "Care of the appliance").
Check the appliance connection and put it into service
following the instructions.
Pasta cooker ignition (Fig. 7, 8 and 9)
Check the water outlet tap is closed (B).
mounted on units the tap is beneath the tank. Fill the tank
with water to the overflow hole, by turning the knob (F).
Turn on the main switch upstream from the appliance. Turn
the knob (A) to 1 or 2 of you want partial power output, or
to 3 for maximum power output. On model E6CP3B you
can regulate the water temperature by turning the knob
(A) to the required position.
When the knob "A" is turned, the light "C" comes on, which
indicates the elements are operative.
To turn the appliance off turn the knob (A) to "0" and turn
on the main switch.
| 55
EN
In models