Bimar PTR1 Manual De Instrucciones página 11

Fax +32 030 9904733
INSTALLATION
• After unpacking, check the integrity of the appliance; if in doubt, do not use and contact a qualified
technician. The packaging materials (plastic bags, polystyrene, metal staples, etc.) must not be left
within reach of children, as they constitute possible sources of danger and must be disposed of
according to applicable regulations.
• Before connecting the appliance, verify that the voltage values on the adapter's plate match with
those of the electric system. Should the socket and the adapter's plug be incompatible, have the
former replaced with a correct one by a professional operator. The use of adaptors or extensions is
generally not advisable; if it is necessary to use them, they must comply with safety regulations and
the total current (amps) must not be rated lower than the maximum current of the the appliance.
Make sure the extension's plug the adapter is connected to is well shielded from water. Should it
come in contact with water, first disconnect the extension's power acting on the switch, then
remove the plug from the mains. Carefully dry both the adapter and the socket before restoring
power.
• Before each use, ensure that the appliance is in good order, that the power cable is not damaged: if
you have any doubts, consult a qualified professional.
• The plug point must be easily accessible so as to easily remove the adapter in case of an
emergency.
• The appliance must not be placed directly beneath a plug point.
• The surface where the appliance is used must be stable, spacious (do not use on shelves), and level.
• Place the appliance far from any sources of heat (stoves, heaters), curtains, tapestries, wood
flooring, electrical appliances (such as computers, precision tools, etc.) or delicate furniture that
could get damaged by water.
• Place the mat far from any other source of heat, from flammable material (curtains, tapestries, etc.),
from flammable gases or flammable material (spray cans) and from materials that can be deformed
by heat. Make sure the is a 100 cm span in the front and 50 cm spans on both sides and in the back.
• Do not use the appliance near a bathtub, a shower box or a swimming pool (to prevent drops of
water from reaching the appliance or the appliance itself from falling into the water), or where it
can be bumped. If water comes in contact with the adapter, first disconnect it from power by
toggling the electrical switch on the board to off, then remove the adapter from the socket.
Carefully dry both the adapter and the socket before restoring power. If in doubt consult a qualified
professional.
• Make sure the cable is positioned correctly and that it is not winded on the appliance or on itself
and that it cannot get caught, to prevent the appliance from falling. Make sure there's no risk to
stumble upon it, to prevent your pet or people from falling over or being injured. Also make sure
the cable is not under a carpet.
• Make sure that the appliance works correctly: if not, turn it off and consult a qualified professional.
• If there is a fault or the appliance is not working correctly, switch it off and have it checked by a
qualified professional. Repairs done by an unqualified person can be dangerous and cause the
guarantee to become void. For safety reasons, the mat and the adapter cannot be disassembled or
opened up.
FUNCTIONING
Attention: always disconnect the appliance from power when left unattended, and before assembling,
disassembling or cleaning.
The appliance consists of the following parts:
- 230AC/12VDC adapter: it powers the appliance.
- Mat is connected to the adapter with plug.
- Cover is made of synthetic wool. The zipper must remain completely closed when the device is
running, open it to remove the mat.
Copies of the I/B. Please reproduce them without any
changes except under special instruction from Bimar
(Italy). The pages must be reproduced and folded in
order to obtain a booklet A5 (+/- 148.5 mm width x 210
mm height). When folding, make sure you keep the good
numbering when you turn the pages of the I/B. Don't
change the page numbering. Keep the language
integrity.
11 32
/
Assembly page 11/32