Idiomas disponibles
Idiomas disponibles
HYGROSTAT HIG
HYGROSTAT HIG
High levels of Humidity is detrimental to the level of quality in the ambient
High levels of Humidity is detrimental to the level of quality in the ambient
air.
air.
The HIG Hygrostat allows control of this level by switching the fan when the
The HIG Hygrostat allows control of this level by switching the fan when the
Relative Humidity (RH) is higher than the preset limit.
Relative Humidity (RH) is higher than the preset limit.
When the Relative Humidity falls to the preset value, the fan will continue to
When the Relative Humidity falls to the preset value, the fan will continue to
work for a period of time adjustable between 1 and 25 minutes.
work for a period of time adjustable between 1 and 25 minutes.
MOUNTING AND ELECTRICAL WIRING
MOUNTING AND ELECTRICAL WIRING
Do not install the sensor too close to a signifcant source of heat.
Do not install the sensor too close to a signifi cant source of heat.
Mounting
Mounting
Fix the HIG at a height of 2 metres above the foor level and in such a way
Fix the HIG at a height of 2 metres above the fl oor level and in such a way
that the air circulates freely. Avoid installation close to a door, a window, or
that the air circulates freely. Avoid installation close to a door, a window, or
in a corner.
in a corner.
T o fx the HIG to the wall, simply carefully remove the front cover by
To fi x the HIG to the wall, simply carefully remove the front cover by
loosening the screw at the bottom. Fix the box in the place choosen through
loosening the screw at the bottom. Fix the box in the place choosen through
the holes in the base.
the holes in the base.
Electrical wiring
Electrical wiring
Before commencing the wiring of the sensor, ensure that the mains supply
Before commencing the wiring of the sensor, ensure that the mains supply
is disconnected.
is disconnected.
In the installation there must be a double pole switch with an opening of at
In the installation there must be a double pole switch with an opening of at
least 3 mm between contacts.
least 3 mm between contacts.
Adjustment (60 - 90% HR)
Adjustment (40 - 90% HR)
T o be active, the HIG needs 15 minutes of operation in the normal
To be active, the HIG needs 15 minutes of operation in the normal
conditions of use.
conditions of use.
When the HIG is connected to the mains supply, the green indicator 1 will
When the HIG is connected to the mains supply, the green indicator 1 will
light.
light.
The yellow light 3 indicates that the ambient air has an RH rate above the
The yellow light 3 indicates that the ambient air has an RH rate above the
selected value.
selected value.
The small wheel marked RH can be used to adjust the required level of
The small wheel marked RH can be used to adjust the required level of
Humidity.
Humidity.
The wheel marked «t» is for adjusting the timer of the HIG. This timer
The wheel marked «t» is for adjusting the timer of the HIG. This timer
activates when the level of air quality reaches the selected value, to ensure
activates when the level of air quality reaches the selected value, to ensure
a complete ventilation of the room.
a complete ventilation of the room.
The yellow indicator 2 will light while the fan is working during timer
The yellow indicator 2 will light while the fan is working during timer
operation.
operation.
Technical characteristics
Technical characteristics
Voltage:
Voltage:
Maximum load:
Maximum load:
Working temperature range: 0 / 40 °C.
Control range:
Working temperature range: 0 / 40 °C.
Appliance of Class II:
Appliance of Class II:
single phase, 230V 50Hz
single phase, 230V 50Hz
6(2) Amps
6(2) Amps
60 / 90% HR
(double insulation)
(double insulation)
