Idiomas disponibles
Idiomas disponibles
English
Our products are engineered to meet the
highest standards of quality, functionality and
design. We hope you enjoy your new Braun
FreeStyle.
Notice: Remove the sole plate label, if any,
before first use.
–––––––––––––––––––––––––––––––––––––––––
Important safeguards
Before using the iron, read the use instruc-
•
tions completely. Keep the use instructions
during the entire life of the iron.
Make sure your voltage corresponds to the
•
voltage printed on the iron. Connect the
iron to alternating current only.
Always unplug the iron before filling with
•
water and make sure the steam button is
in its lower position (steam off). Always pull
the plug, not the cord. The cord should
never come in contact with hot objects or
with the hot sole plate.
Never immerse the iron in water or other
•
liquids.
During ironing pauses, always place the
•
iron upright on its heel rest. Unplug it when
leaving the room, even if only for a short
time.
Never pull out the steam button (3) during
•
ironing.
Keep the iron away from children.
•
Electric irons combine high temperatures
and hot steam that could lead to burns.
Check the cord regularly for possible
•
damage.
If the appliance (including cord) shows any
•
defect, stop using it and take it to a Braun
Service Centre for repair.
Faulty or unqualified repair work may
•
cause accidents or injury to the user.
–––––––––––––––––––––––––––––––––––––––––
A Description
1 Spray nozzle
2 Water tank opening
3 Steam button
3a Steam regulator
4 Spray button
5 Power shot button
6 Temperature selector
7 Temperature pilot light
B Before starting off
This iron is designed for tap water. If you
•
have extremely hard water, we recommend
to use a mixture of 50% tap water and
50% distilled water. Fill the water tank to
«max» marking. Never use distilled water
exclusively. Do not add any additives
(e.g. starch).
Keep the iron in the upright position and
•
connect it to the mains. Select the tem-
perature according to the ironing guide on
the heel rest of the iron or on the label in
your garments.
The temperature pilot light (7) goes off,
•
when the desired temperature is reached
(after approx. 1 minute).
C Ironing
1 Steam on/off
For steam ironing, the temperature selector
(6) must be set within the red range.
Press the steam button (3) to start the
steam mode.
steam on
With the steam button in its upper position,
turn the steam regulator (3a) to adjust the
steam quantity.
Preconditioning
(not with models SI 6210, SI 6510)
Steam develops also horizontally at the
front area of the sole plate. This pre-
conditions the textiles by «pre-steaming»,
thus making ironing easier.
Be careful – steam comes out laterally.
2 Power shot
Prior to use, press the power shot button
(5) 3 to 4 times to activate it. Press the
power shot button in intervals of at least
5 seconds.
Power shot can be activated when dry
ironing. However, the temperature selector
has to be set in the range between «•••»
and «max». The power shot function can
also be used in the vertical position for
steaming hanging clothes.
3 Spray function
Press the spray button (4).
4 Dry ironing
Turn the steam mode off by pressing the
steam button (3) so that it catches in the
lower position.
D After ironing
Unplug the iron and press the steam on/off
•
button (3) so that it catches in its lower
position (steam off).
To prolong the life of the iron, empty the
•
water tank.
Store the cool iron in a dry place always
•
standing on its heel rest.
E Maintenance and cleaning
To clean the sole plate, use steel wool.
Then wipe the sole plate clean with a cloth.
Never use a scouring pad, vinegar nor
other chemicals. To clean the soft material
of handle and power shot and spray
buttons, use soapy water.
5
steam off
F Cleaning the anticalc valve
The iron's anticalc valve is located at the
lower end of the steam button (3). It has
to be decalcified regularly (e.g. when the
steam development is insufficient).
Proceed as follows:
1) Unplug the iron and empty the water tank.
2) Press the steam button so it is lifted.
3) Remove carefully (some water may now
leak from the sole plate).
4) Do not touch the anit-calc valve.
5) Immerse in vinegar (not vinegar essence)
or lemon juice until the lime becomes soft.
6) Use a non-metallic brush until all openings
are clean.
7) Rinse under running water.
8) Re-insert the steam button.
9) Press to check the steam on/off function.
Note: the iron must never be used without
the steam button.
G Decalcifying / anticalc system
When scale particles come out of the
steam vents or when the steam
development is insufficient even after
cleaning the anticalc valve, you should
clean the steam chamber as follows:
1) Make sure the steam button is in its lower
position.
2) – 3) Fill water into the tank, connect to the
mains and select the «•••» temperature
setting.
4) – 5) Wait until the pilot light turns off.
Unplug the iron.
6) – 7) Hold the iron over a sink, then press the
steam button so it is lifted, carefully pull it
up, turn it and rest it in this position.
Caution: When the steam button is pulled
up, hot water and steam will come out from
the sole plate.
8) Push back the steam button until it catches
in the lower position.
9) – 10) Fill water into the tank, connect to the
mains and select the «•••» temperature
setting.
11) – 13) When the pilot light goes off, press
the power shot button 4 times to rinse the
iron. Disconnect the iron and wait for the
sole plate to cool off, then clean it as
described above in section E.
Note: the iron must never be used without
the steam button.
H Trouble-shooting guide
Problem
––––––––––––––––––––––––––––––––––––––
Drops
coming out
of the steam
vents
No steam
at all
Less steam
develops or no
steam at all
Calcium
particles
coming through
the steam vents
––––––––––––––––––––––––––––––––––––––
Subject to change without notice.
This product conforms to the
EMC-Requirements as laid down
by the Council Directive 89/336/EEC
and to the Low Voltage Regulation
(73/23 EEC).
Remedy
Turn the steam regulator
anti-clockwise to reduce
the steam or press the
steam button to turn the
steam off.
Take longer intervals
when pressing the power
shot button.
Select a higher tempera-
ture setting.
Press the steam button
so that it is lifted.
Clean the anticalc valve
(see F).
Decalcify the steam
chamber (see G).
