Chicco Key 23 Instrucciones De Uso página 34

Components
A. Headrest
B. Slot for recline adjuster handle lock/release button
C. Backrest
D. Armrests
E. Backrest rear panel
F. Seat
G. Headrest adjustment lever
H. Handle for adjusting the width of the backrest
I. Velcro straps
J. Zips
K. Fabric cover
L. Rear pocket
M. Diagonal belt clamps
N. Side wings
O. Side pillows
P. Lap belt holes
Q. Upper part of the seat
R. Lower part of the seat
S. Backrest/seat joint
T. Press studs for fixing the fabric cover to the seat
U. Seat inclination adjuster handle
V. Handle for locking/unlocking the seat
W. OPEN symbol
X. CLOSE symbol
Y. Reference circles
How to Fit the Child Car Seat into the Car
and Place the Child into the Child Car Seat.
Warning! These instructions and diagrams are
for the installation of the child car seat onto
the right rear seat. To fit the child car seat in
other positions, carry out the operations in the
same order.
1. Place the child car seat on the car seat, lean-
ing the backrest against the backrest of the
car's seat (diag. 6).
CAUTION! Check that the headrest of the car
seat does not interfere with the headrest of
the child car seat: it must not be pushed for-
ward (diag. 7). Should this happen, remove the
headrest of the car seat, on which the child car
seat will be fitted to, and remember to replace
the headrest back onto the car seat, when the
child car seat is removed, so that the car seat
can be used once more by a passenger. .
WARNING! The rear part of the child car seat
must fit perfectly to the car's seat (diag. 8).
2. Place the child into the child car seat, en-
suring that its back adheres correctly to the
backrest (diag. 9).
3. Check the height of the headrest and ad-
just if it is not correct: see the paragraph
"HOW TO ADJUST THE HEIGHT OF THE
HEADREST".
4. Check the width of the backrest, and adjust
it if necessary: see the paragraph "HOW TO
ADJUST THE WIDTH OF THE BACKREST".
5. Fasten the safety belt of the car, sliding the
horizontal part under the two armrests, in
the points highlighted in red, and the di-
agonal part under the armrest, located on
the side of the safety buckle (diag. 10).
6. Slide the diagonal part of the safety belt
through the red clamp (diag. 11).
7. Pull the diagonal part of the car seat belt to-
wards its retractor, ensuring that the safety
belt is well tensioned and that it fits cor-
rectly to the child's abdomen and legs. The
safety belt must not be too tight! (Diag. 12).
The child car seat is now fitted correctly
(diag. 13).
WARNING! Check that the safety belt of the car
is correctly tensioned.
WARNING! Check that the safety belt of the car
is not twisted (diag. 14).
WARNING! Check that the diagonal belt is fas-
tened correctly on the child's shoulder (diag.
15), and that it does not exercise pressure on
its neck; if necessary, lower the headrest.
WARNING! Check that the car seat safety belt
adjuster is either in a backward position with
respect to the backrest of the car seat (or at
least aligned to it)(see diag. 5).
WARNING! Never use the car safety belt in any
other positions that those indicated in this in-
structions booklet! (diag. 16).
WARNING! Do not let your child slide forward
or downward.
How To Remove The Child From The Child
Car Seat
1. Unfasten the car safety belt.
2. Remove the diagonal part of the car safety
belt form the clamp.
3. Hold the safety belt and ease it into the retractor.
How to Fit the Child Car Seat into the Car
without the Child
Carry out operations 1,5,6,7 as described in
34